|
|
|
说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
|
|
|
您的位置： 首页 -> 词典 -> 控制器组件螺栓孔
1) control group bolt hole
控制器组件螺栓孔
2) bolt groupware
螺栓组件
1.
The factor which influenced the performance of tension fatigue and anti-loosen for bolt groupware were found and the feasibility of reforming project of hanging bolt for traction motor was verified through analyzed the results of the test.
针对"蓝箭"动车组牵引电机悬挂螺栓折断,为了验证螺栓改造方案,对模拟在装车状态下的螺栓的疲劳及防松性能进行了研究,通过对试验结果的分析,得出了影响螺栓组件的抗拉疲劳强度及防松性能的因素,验证了牵引电机悬挂螺栓安装方式的改造方案的正确性。
3) hinged bolts
铰制孔螺栓
1.
In this paper, the mechanism that because of the local failure of hinged bolts for joining rigid couplings during power transmission of marine shafting, their shear stresses differ from each other is presented, the mechanical analysis and program calculation are made, and a practical calculation software is provided.
介绍了船舶轴系在传动中,因联结刚性联轴器铰制孔螺栓的局部缺陷,导致各个螺栓强度不均的机理,进行了力学分 析和程序计算,并提供了一个实用计算软件。
2.
In order to solve the joint bolts fracture problem between the ball mill tube and flange,from the theoretical investigation,through the force analysis and the stress checking of the joint bolts,the reasonable hinged bolts number requst is got.
从理论研究的角度出发,通过对螺栓的受力分析及应力校核,得到铰制孔螺栓的合理数目要求,为以后设计及生产提供了理论依据。
4) gyro-control unit
陀螺控制组件
5) controller module
控制器组件
6) bolt which is controlled
控制紧螺栓
1.
Can be used by the special operator of bolt,discussing the calculation about the limit load of bolt in the changing temperature particularly,satisfying the request of the design for loose bolt and close bolt which is controlled in the low temperature.
针对温度影响螺栓强度设计的难点,详细探讨变化温度螺栓极限载荷的计算,满足该温度区间下松螺栓设计、控制紧螺栓设计的要求,可供螺栓专业设计参考。
补充资料：齿轮轮齿渐开线、螺栓、弹簧autolsp源程序
一、齿轮轮齿渐开渐开线 (defun c:gear(/)
(
setq
p0 (getpoint"输入齿轮中心p0: ")
m (getreal"输入齿轮模数M: ")
z (getint"输入齿轮齿数Z: ")
ha 1
c 0.25
a (/ pi 9)
ra(/ (* (+ z (+ ha ha)) m) 2)
rf(/ (* (- z (+ (+ ha ha) c)) m) 2)
r(/ ( * m z) 2)
rb ( * r (cos a))
ri rb
ang 0
g (polar p0 ang rb)
)
(command "circle" p0 ra)
(command "circle" p0 rf)
(command "circle" p0 r)
(command "line" g)
(while (< ri ra)
(setq
ang ( + ang(/ pi 360))
ri ( / rb (cos ang))
cta ( - (/ (sin ang) (cos ang)) ang)
g(polar p0 cta ri)
) (command g)
)
(command )
)
二、螺旋源程序
(defun errMsg (s)
(if (/= s "function cancelled") (princ (strcat "\nError: " s)))
; 当命令执行时出现错误
(setvar "cmdecho" ocmdold) ; 例如用户按下了CTRL + C
(setvar "osmode" osmold)
(setq *error* olderr) ; 恢复旧的错误处理
(princ)
) (defun c:3Dthread (/ radouter threadpitch threadlength threadangle
ptStart innerdiafactor radmid radinner ocmdold osmold 4H 5H 6H h6 g6)
;-------------------------------------------------------------------
; 获取公制外径大小、螺距总长
; 然后计算一系列几何点
; 并且关闭对象捕捉、命令回显
;-------------------------------------------------------------------
(setq 4H (list 0.0015 0.002 0.002 0.0025 0.003 0.0035 0.004 0.005 0.006 0.007 0.008 0.009 0.010))
(setq 5H (list 0.002 0.0025 0.003 0.004 0.0045 0.0055 0.0065 0.0075 0.009 0.010 0.0115 0.0125 0.0135))
(setq 6H (list 0.003 0.004 0.0045 0.0055 0.0065 0.008 0.0095 0.011 0.0125 0.0145 0.016 0.018 0.020))
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|