说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 敲松间隙(拔模型用)
1)  block print clearance
敲松间隙(拔模型用)
2)  intermittent model
间隙模型
3)  extraction space
拔牙间隙
1.
Soft-and hard-tissue changes after extraction space closure with micro-screw implant
微螺钉种植支抗关闭拔牙间隙后软硬组织的变化
2.
The diameters of the post extraction spaces and curvature of spee\'s curve measured at the time of 4 months after the first premolar\'s extraction were compared with that mea-sured at the time of 30 minutes after the first premolar\'s extraction.
分别测量两组病例拔牙后30min、4个月时拔牙间隙近、远中方向最小径,比较分析两者拔牙间隙变化情况和Spee\'s曲线曲度。
4)  outer gap model
外间隙模型
1.
In the frame of the revised outer gap model,study the non-thermal X-ray radiation of seven old pulsars observed by Chandra, the predicted values are consistent with the observed date, and calculate the non-thermal X-ray luminosity of old pulsars with outer gaps, and compute the gamma-ray luminosity and gamma-ray fluxes of these old pulsars with outer gaps.
利用新的外间隙模型,研究计算了老年脉冲星的非热X-射线光度,并与Chandra观测到的七颗老年脉冲星的非热X-射线光度的观测结果进行了比较,模型的计算结果和观测数据吻合较好,同时计算了老年脉冲星可能的伽玛射线光度和流量。
2.
This paper studies the outer gap model of pulsars,analyzes the differences between traditional outer gap model and the new one,and points out that the electric field created from the pulsar surface is very strong but the electric field along the magnetic field is almost zero,and charged particles are accelerated to relativistic energy in outer gap resulting in high energy radiation.
研究了脉冲星的外间隙模型,分析了传统的外间隙模型和新的外间隙模型之间的不同之处。
5)  Clearance [英]['klɪərəns]  [美]['klɪrəns]
松旷间隙
1.
Study on the Automatic Testing Method for the Clearance of Automobile Transmission System;
汽车传动系松旷间隙自动化检测方法研究
2.
Discusses on the Automatic Detection Method for Clearance at Wheel Hub Bearing and Kingpin;
汽车轮毂轴承及主销松旷间隙自动化检测方法探讨
6)  slack adjuster
松动间隙
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条