1) warning centre
警戒中心 WC
2) tungsten carbide
WC
1.
Micro defects in tungsten carbide particulates reinforced steel matrix composites by electroslag melting and casting;
电冶熔铸WC/钢复合材料的显微缺陷
3) detonation spraying
WC-12Co
1.
The nanostructured and conventional WC-12Co coatings are prepared by detonation spraying,and the properties of two coatings such as microhardness,adhesion and wear resistance are investigated,and the characterization of the spraying powders and coatings are analyzed by scanning electron microscopy(SEM).
采用爆炸喷涂工艺分别制备纳米结构和常规结构WC-12Co涂层,研究了2种涂层的显微硬度、结合强度和摩擦磨损性能,并用扫描电镜(SEM)分析喷涂材料和涂层的形貌。
4) WC powder
WC粉
1.
Description is made of a new technology for preparing WC powder by carburizing in a mixture gas medium developed by professor V.
介绍了乌克兰国家科学院超硬材料研究所VPBondarenko教授研究小组开发的一种气相法制备WC粉新技术。
2.
The test mode of using OMEC LS_POP(Ⅲ) particle size analyzer to test all of the particle sizes of W powder and WC powder is discussed, the effect of factors such as milling time, rate of lightproof, refractive index and sampling time on coarse, medium and fine size distributions are selective tested, the results are satisfied.
采用OMECLS -POP(Ⅲ)型激光粒度分析仪对各种粒径的W粉、WC粉粒度分布的测试方法进行了探讨 ,对研磨时间、遮光比、折射率和采样时间等因素对粗、中、细颗粒粒度分布测试的影响进行了选择试验 ,测定结果令人满意。
3.
Study is made of the genesis of the aggregate in WC powder.
对WC粉中聚集体的成因进行了试验研究。
5) WC phase
WC相
1.
The microstructure and twin deformation properties of WC phases were investigated by loading alloy specimen.
结果表明,当WC为单一相时,WC相能产生孪生-滑移协调变形,从而使该合金具有较高的韧性。
2.
The microstructure of WC phase of YG11C carbides is investigated by means of TEM which is manufactured by Zigong Cemented Carbide Corp.
对自贡硬质合金有限责任公司生产的YG11C合金进行了仔细的TEM研究,了解其WC相的微观结构,结果表明,在WC相中,除了存在WC相外,还存在着W2C、WC(1-X)等相。
6) w_V/w_C
wV/wC
1.
The effects of w_V/w_C on high-temperature wear property of Cr-Mo-V cast hot-forging die steel were studied.
研究了不同wV/wC对Cr-Mo-V精铸热锻模具钢的高温磨损性能的影响,并探讨了其磨损机理。
补充资料：WC-TiC-Co hard alloy
分子式：
CAS号：
性质：又称钨钛钴合金或YT合金。碳化钨、碳化钛和金属钴组成的合金。按碳化钛含量，可分为高钛(25％～40％)、中钛(10％～20％)和低钛(4％～6％)三类合金。它比碳化钨钴合金具有较高的抗氧化性，硬度和耐磨性，而抗弯强度、冲击韧性等则有所降低。主要用作切削加工钢材的工具。
CAS号：
性质：又称钨钛钴合金或YT合金。碳化钨、碳化钛和金属钴组成的合金。按碳化钛含量，可分为高钛(25％～40％)、中钛(10％～20％)和低钛(4％～6％)三类合金。它比碳化钨钴合金具有较高的抗氧化性，硬度和耐磨性，而抗弯强度、冲击韧性等则有所降低。主要用作切削加工钢材的工具。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条