1) constant speed scanning
等速扫描
2) scan speed
扫描速度
1.
The optimal distance among casing connection and probe can be further researched and the relationship between arrayed probes and scan speed can be demonstrated more clearly from this arrayed system.
根据超声聚焦探头的测厚原理,分析聚焦探头的焦距和晶片尺寸与聚焦声束的关系,选择合适的聚焦探头组成阵列式多探头自动化壁厚检测系统,进一步研究探头与石油套管之间的最佳距离和阵列式多探头与扫描速度之间的关系。
3) scanning velocity
扫描速度
1.
Calibration of scanning time and scanning velocity for high speed imageconverter camera;
高速变像管相机扫描时间和扫描速度的标定技术
2.
From the view of theory and practice, it presents that laser output power P, scanning velocity V and the diameter of faculae E are fundamental technological parameters in treatment with laser.
论述了激光表面硬化处理中影响硬化质量的决定因素 ,并从理论和实践角度说明激光输出功率 P、扫描速度 V和光斑直径 D才是激光处理的基本工艺参
3.
The results show that were different from power density and scanning velocity its in the surface of hardening layer microstructures and properties also different from, when power density W>4.
对灰口铸铁H2 0 40在激光加热条件下不同的功率密度 (W )、扫描速度 (V)对硬化层深度、硬度及组织进行了系统的研究 。
4) scan rate
扫描速率
1.
Effect of scan rate on nonafriction properties of monolayer molecular deposition film on silicon;
扫描速率对硅表面分子沉积膜纳米摩擦特性的影响
2.
In addition,the effect of scan rate on peak current and potential was studied when a film CuX was formed,and the mechanism of dissolution o.
通过比较Cu在卤离子溶液与含 (NH2 ) 2 CS卤离子溶液中的电化学行为 ,解释了 (NH2 ) 2 CS的缓蚀机制 ;并研究了扫描速率对形成CuX膜的峰电位和峰电流的影响 ,探讨了Cu的阳极溶解机
5) scanning speed
扫描速度
1.
Influence of laser scanning speeds on microstructure and properties of cladding layer WC-B_4C-SiC-Co;
激光扫描速度对WC－B＿4C－SiC－Co熔覆层组织和性能的影响
2.
Influence of scanning speeds on microstructure and properties of laser cladding WC-B_4C-Co;
扫描速度对激光熔覆WC-B_4C-Co涂层显微组织和性能的影响
3.
Influence of Scanning Speed on Mold Shrinkage of Nylon 6 Prepared by Selective Laser Sintering;
扫描速度对选区激光烧结制备尼龙6收缩行为的影响
6) scanning rate
扫描速率
1.
The performance test of MOD300 distributed control system is described in this paper and an analysis on the test results of 3 primary performance indexes——system response time, scanning rate and CPU load rate——was carried out.
本文介绍了北仑电厂1号机MOD300分散控制系统性能测试的情况,并对三个主要性能指标:响应时间、扫描速率和CPU负荷率的测试结果作了分析,对如何提高系统响应速度、降低CPU负荷率提出了建议。
2.
It was focused on design of the optimization about the parameters on the selective laser sintering processing,such as scanning rate,power of sintering and preheated temperature.
对ABS粉末塑料的选区激光烧结过程的成型工艺参数进行了优化设计,对其中影响最大的参数(扫描速率、激光功率、预热温度)的匹配以及成型参数的选择进行了优化设计,得出一组最佳组合的工艺参数。
补充资料：扫描电子显微镜(见扫描电子显微术)
扫描电子显微镜(见扫描电子显微术)
scanning eleetron mieroseoPe
扫描电子显微镜scanning eleetron mieroseope见扫描电子显微术。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条