2) substructure
[英]['sʌbstrʌktʃə(r)] [美]['sʌb'strʌktʃɚ]
底座
1.
Design model for new rig derrick and substructure;
新型钻机井架及底座设计模型
2.
Recnstruction of the derrick and substructure for Daqing 130 rig;
大庆130型钻机井架和底座的改造
3.
For the mast and substructure,as the drilling rig's main components,the structural design project,mostly,of its influence and decide general arrangement of the drill rig.
井架、底座作为石油钻机的主要部件,其结构方案的优劣很大程度上影响和决定着钻机方案的优劣,在超深井钻机设计中,井架、底座技术更是钻机的关键技术之一。
3) base
[英][beɪs] [美][bes]
底座
1.
Several methods for lifting the base of porwered support are introduced,The way to reduce the load intensity on the front edge of powered suppord base is proposed by means of analysis and test,Two design instances are provided.
介绍几种液压支架抬底座的方法，通过分析和试验提出减小支架底座前端比压的方法，并提供了设计实
2.
0 as the base of pump carries out Finite element analysis,it not only gets its stress and deformation to meet an emergency to but also gives inherent frequency and the form of vibration.
0对水泵底座进行了有限元分析,获得了在载荷作用下结构的应力、应变值和结构的固有频率和振型。
3.
The finite element model is established and analyzed by using AUTODESK INVENTOR and ANSYS WORKBENCH,by which the strain and stress of the base during opening and closing are calculated.
利用AUTODESK INVENTOR和ANSYS WORKBENCH软件对某大型水工闸门的底座结构进行分析,计算了结构在开启和关闭过程中产生的应力和应变,从而验证所设计的底座结构能够满足系统的刚/强度指标要求,为水工闸门底座设计提供有益的参考。
4) foundation
[英][faʊn'deɪʃn] [美][faun'deʃən]
底座
1.
Structural analysis and improvement on the foundation of TLJ400 continuous extrusion;
TLJ400连续挤压机底座的结构分析与改进设计
2.
During hanging the frame and driving pile,the frame foundation,guide columniation and supports would be affected by multiple forces that would affect the intensity design and structure design of the frame.
在起吊和打桩过程中,导向架底座、立柱和支撑会受到各种力的作用,这些力将对其强度和结构设计产生重要影响。
5) pedestal
[英]['pedɪstl] [美]['pɛdɪstḷ]
底座
1.
Aseismatic Analysis and Parameter Optimization of Pedestal about Nuclear Engineering Gear Pumps Unit;
核电工程用齿轮泵机组底座的抗震分析及参数优化
2.
Based on a finite element model of the pedestal of crane,five dangerous cases have been analyzed,and some relevant measure to improve the strength of structure have been put forward.
在建立克令吊底座加强有限元模型的基础上,对5种危险工况进行了计算分析,并提出了有效的改进措施,保证了克令吊底座的强度要求。
6) socle
[英]['sɔkl] [美]['sɑkḷ]
底座
1.
This paper show: if M is a ring with the prime radiCal P(M), the socle Soc(M),the nil radical N(M) and the Levitzki nil radical L(M),then regarded as a Pring with P=M,Pp(M)=P(M),Socp(M)=Soc(M),Np(M)=N(M) and LP(M)=L(M).
证明了如果Ｍ是一个环，具有素根Ｐ（Ｍ），底座Ｓｏｃ（Ｍ），诣零根Ｎ（Ｍ）和Ｌｅｖｉｔｚｋｉ诣零根Ｌ（Ｍ），则Ｍ作为一个Γ－环（取Γ＝Ｍ）有：Ｐ（Ｍ）＝ＰΓ（Ｍ），Ｓｏｃ（Ｍ）＝ＳｏｃΓ（Ｍ），Ｎ（Ｍ）＝Ｎｒ（Ｍ）和Ｌ（Ｍ）＝ＬΓ（Ｍ
2.
This paper shows that the Jacobson radical and socle of a graded gamma ring of type Z are graded ideals, obtains some relations between the graded Jacobson radical(graded socle) and the Jacobson radical (socle) of a graded gamma ring, and gives some basic results of chain conditions of a gamma ring.
证明了Ｚ－型分次Γ－环的Ｊａｃｏｂｓｏｎ根和底座是分次理想，得到一系列有关分次Γ－环的分次Ｊ－根（分次底座）与Ｊ－根（底座）之间的关系式，并给出Γ－环的链条件的一些基本结果。
补充资料：底座
1.物件底部的座子。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条