1) profiloscope
拉丝模孔光洁度
2) ultrasonic drawing die drilling machine
超声波拉丝模打孔机
3) Aperture measuring instrument for drawing die
拉丝模孔径测量仪
4) smoothness
[英]['smu:ðnis] [美]['smuðnɪs]
光洁度
1.
The concentricity and smoothness of the parts are guaranteed.
通过定制的工艺装备,将一种小电机中的环形薄壁零件加工至要求尺寸,并保证零件的同轴度和表面光洁度。
2.
It analyzes the arched culvert construction scheme and technology before the construction,represents the die processing and setting and concrete construction,and introduces form board joint junction treatment technology and method on the special position,which will insure the smoothness of concrete external appearance.
对施工前拱涵的施工方案及工艺进行了分析,并对模具加工安装和混凝土的施工等进行了阐述,介绍了特殊部位模板缝接头的处理工艺及方法,保证了混凝土外观的光洁度。
3.
The smoothness of the alloy for electrochemical and mechanical polishing was assessed;and the potentiodynamic polarization technique was carried out in Hanks solution to verify the corrosion resistance.
与机械抛光作对比, 研究了两种抛光技术对合金表面光洁度的影响,并利用电化学方法研究了抛光技术对合金在 Hanks’溶液中腐蚀性能的影响。
5) smooth finish
光洁度
1.
Rainfall affects surface smooth finish of red Fuji apple;
降水量对红富士果面光洁度的影响
2.
The characteristic of the flow obstruction of water in carbon steel tube, stainless steel tube and red copper tube is determined by the experiment in the paper, superficial roughness and smooth finish of three kinds of tubes are analysed with the instruments;and the obsuruction coefficient difference is analysed and discussed.
对水在无缝碳钢、不锈钢和紫铜管内的流动阻力特性进行了实验测定;对各种表面的粗糙度和光洁度作了仪器分析;对引起阻力系数差异的原因进行了分析讨论。
3.
The smooth finish of siC whiskers was affected by the whisker′s growing supersaturation in some special areas and the pr.
得到的碳化硅晶须以β晶型为主，兼有少量α晶型；晶须有白色，灰白色，灰绿色，深绿色等多种颜色，其颜色变化与原料中的硅炭比值有直接关系；晶须的光洁度受晶须生长局部范围内过饱和度与保护气氛等因素影响；反应原料的堆积密度是影响晶须直晶率的主要因素，稻壳原料生长的晶须其直晶率较高。
6) finish
[英]['fɪnɪʃ] [美]['fɪnɪʃ]
光洁度
1.
The influence of ingredient, temperature and time of the polishing solution workpieces surface finish is discussed.
研究了奥氏体不锈钢细长弯管的化学抛光液的组成及抛光工艺参数 ,讨论了抛光液的组成成分和抛光温度、时间对表面光洁度的影响 。
2.
It is emphasised to discuss about toughening methods ,cracks and their eliminating methods, surfacefinish, fire retardance in the process of development of BMC pasts.
重点讨论了研制中主要问题 ,开裂、光洁度等的分析解决。
补充资料：拉丝
分子式：
CAS号：
性质：(一)胶黏剂在配制后因超过活性期，胶液部分凝聚所产生的在拉伸情况下成为丝状物的现象。(二)涂料在喷涂时雾化不好，致使涂料不能化为微细的雾滴而呈丝状喷出，所得的涂膜不能流平，出现了拉丝。原因是涂料施工黏度高，稀释剂溶解力差。宜选用适合的溶剂，调整到适宜施工黏度，使涂料在喷涂时能充分雾化，能流平，即可避免此弊病。
CAS号：
性质：(一)胶黏剂在配制后因超过活性期，胶液部分凝聚所产生的在拉伸情况下成为丝状物的现象。(二)涂料在喷涂时雾化不好，致使涂料不能化为微细的雾滴而呈丝状喷出，所得的涂膜不能流平，出现了拉丝。原因是涂料施工黏度高，稀释剂溶解力差。宜选用适合的溶剂，调整到适宜施工黏度，使涂料在喷涂时能充分雾化，能流平，即可避免此弊病。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条