1) breaking length
断裂长
2) breaking elongation
断裂伸长
1.
The chemical and physical properties of the feather fiber were evaluated with weight loss,breaking strength and breaking elongation.
采用质量损失率和断裂强力、断裂伸长等指标,客观评定常温下羽毛纤维的耐化学试剂性能。
2.
Addition of the kind will help improve ammonia fibre's breaking strength and breaking elongation,and prohibit yellowing of its thread.
探讨了ANCH添加剂对氨纶耐氯性能的影响,使用这种添加剂后,可以提高氨纶耐氯的断裂强度、断裂伸长,同时可以抑制氨纶丝的泛黄。
3.
Influence of polypropylene tow fiber on hardness, weight, circumference, sucking resistant index of filter stick and finished filter stick rate was discussed under different breaking tenacity and breaking elongation.
本文介绍了烟用聚丙烯丝束在不同断裂强度、断裂伸长的情况下 ,丝束对其成棒后滤棒之硬度、重量、圆周、吸阻指标及成棒率的影
3) breaking length
裂断长
1.
It showed that the breaking length and burst index of two pulps were higher than those of an American hardwood pulp,and the strength properties of E.
用漂白麦草浆或漂白针叶木浆与刚－１２桉或尾叶桉木浆配抄，裂断长产生协同效应。
4) elongation breakage
伸长断裂
1.
The paper analyzes the interaction between woven fabric and needle in the integrated piercing process of orthogonal laminated woven fabrics, proposes and establishes fiber bending elongation and elongation breakage model,and talks over the structure parameters influencing fiber bending elongation.
分析了正交叠层机织布整体穿刺工艺机织布与钢针的相互作用 ,提出并建立了纤维的弯曲伸长及伸长断裂模式 ,讨论了影响纤维弯曲伸长的结构参数。
5) breaking length
断裂长度
1.
By analyzing in the regards such as maturing coefficient, average single fiber breaking strength, breaking length and Micron Value of cotton from different growing areas in China, and conducting boiling and blea.
作者对国内不同产地的棉花的成熟系数、平均单根纤维断裂强力、断裂长度、马克隆值等进行了分析,并采用NaOH—H_2O_2法进行了蒸煮漂白试验,初步寻找出了棉花纸浆性能产地差异的规律。
2.
Determination of the breaking length of ice sheet against iceresist structures is one of the basic problems for the analysis on dynamic load and iceenvironment conditions of offshore structures.
依据简化的窄锥冰力模型给出了冰排在锥面上弯曲断裂长度的分析解和无量纲参数(长厚比k)形式给出的结果。
6) long-lived fault
长寿断裂
补充资料：断裂长度
分子式：
CAS号：
性质：纤维本身重量与其拉伸断裂强力相等时的长度，是表示纤维强力和细度的综合指标。单位为km。计算公式为：断裂长度(km)=
CAS号：
性质：纤维本身重量与其拉伸断裂强力相等时的长度，是表示纤维强力和细度的综合指标。单位为km。计算公式为：断裂长度(km)=
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条