2) alloy
[英]['ælɔi] [美]['æl,ɔɪ]
合金;合铸
3) Cast Alloy
铸造合金
1.
On the basis of orthogonal experiment, the effect of Mg content and heat treatment on mechanical properties of near eutectic Al Si cast alloys modified with Sr has been investigated.
以正交试验为基础 ,通过调整Mg含量和热处理工艺 ,分析它们对Sr变质近共晶Al Si铸造合金力学性能的影响。
2.
The effect of carbon content on element segregation and corrosion resistance of the cast alloy Fe 30Ni 20Cr 6Mo has been investigated.
研究了Ｆｅ－３０Ｎｉ－２０Ｃｒ－６Ｍｏ铸造合金中微量元素Ｃ对合金元素偏析和耐蚀性的影响。
3.
Effect of microstructure and element distribution of an iron base cast alloy Cr30Nil7Mo2Cu solidified at different rates upon the erosion-corrosion behaviour in flowing suspension of solid particles in strong acidic medium has been investigated by metallograph, XRD, EPMA and hardness tests.
用扫描电镜、Ｘ射线衍射、电子探针等手段测定及分析了Ｆｅ基铸造合金Ｃｒ３０Ｎｉ１７Ｍｏ２Ｃｕ以不同速度凝固后的显微组织和主要合金元素分布，在含固相颗粒的强酸性双相流介质中测定了冲刷腐蚀性能。
4) alloy cast iron
合金铸铁
1.
Development of alloy cast iron standard materials for spectral analysis;
合金铸铁光谱分析用标准物质的研制
2.
The Cu-Ni alloy cast irons of different chemical constitution were designed,and the corrosion rate in room-temperature concentrated alkaline solution was measured by the static hydrometer method,the microscopics and phase composition of alloy cast iron were observed by optical microscope and XRD.
设计了不同成分的铜镍合金铸铁,并用静态失重法测定其在室温浓碱液中的腐蚀速率,借助光学显微镜和X射线衍射仪分析了显微组织和相组成。
3.
The corrosion rates of Cu-Ni alloy cast irons in hot concentrated alkaline solution were measured by dynamic condition hydrometer method,the microscopic structures and surface corrosion topographies of alloy cast irons were observed by the optical microscope and SEM,the components were analyzed by XES.
采用动态失重法测定铜镍合金铸铁在高温浓碱液中的腐蚀速度,借助光学显微镜和扫描电镜观察显微组织和表面腐蚀形貌,利用能谱仪分析表面微区成分。
5) alloy cast-iron
合金铸铁
1.
To study high-speed machining process of alloy cast-iron, a finite ele ment model (FEM) is built.
为深入研究合金铸铁的高速切削机理,建立了高速切削的有限元模型,对高速铣削合金铸铁时的锯齿状切屑形成过程进行了仿真分析,获得了切削参数对锯齿状切屑形成的影响规律,为优化切削参数、提高刀具寿命和加工表面质量提供了参考依据。
6) alloy electroformation
合金电铸
1.
Then Ni-Mn alloy electroformation tests are carried out for the model of a nozzle.
设计了一种可用于复杂回转形零件电铸的装置,为了改善合金电铸时沉积金属分布的均匀性,该装置采用了特殊结构的象形阳极并利用ANSYS有限元软件对象形阳极进行了精确的轮廓形状设计。
补充资料：铝硅镁铸造合金
分子式：
CAS号：
性质：由铝、镁、硅为主成分的铸造合金。含硅一般在12％以下，同时加入少量铜和镍以增加强度、细化晶粒和使组织稳定化。杨氏模量71.0GPa，冲击值0.74～1.1J，疲劳极限50～80MPa。采用固溶、时效处理和淬火热处理方法制造。用于泵铸造件、支架等。
CAS号：
性质：由铝、镁、硅为主成分的铸造合金。含硅一般在12％以下，同时加入少量铜和镍以增加强度、细化晶粒和使组织稳定化。杨氏模量71.0GPa，冲击值0.74～1.1J，疲劳极限50～80MPa。采用固溶、时效处理和淬火热处理方法制造。用于泵铸造件、支架等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条