1) mold oven
烘模炉
2) baking oven
烘模炉，干燥炉
3) oven
[英]['ʌvn] [美]['ʌvən]
烘炉
1.
The masonry of rotary kiln and operation of drying oven of limestone ore are introduced.
介绍了石灰石矿回转窑的砌筑及烘炉施工情况,按照耐材砌筑施工规范与要求,采取控制烘炉升温等措施,确保回转窑砌筑成功,并快速实现正常生产,达到设计水平。
2.
The substitute,light diesel oil,has been used as the fuel of oven and blow-in system.
随着沸腾炉向大型化方向的发展,原有的以木柴及焦炭为燃料烘炉及开炉的方法,已不能适应现代生产的需要。
3.
The influence of oven s hearth structure on heat transfer efficiency is analyzed in this paper, and several improving methods are presented.
分析了烘炉炉膛结构对换热效率的影响 ,并提出了几种改进的方法。
4) baking furnace
烘炉
1.
A series of measures,such as baking furnace before blowing-in,improving coke quality,screening below ditch,testing feed influent track etc.
重点阐述了2000 m3高炉冶炼钒钛矿开炉前的烘炉、焦炭质量改善、沟下过筛、料流轨迹测试等工作。
2.
2 ironmaking plant, the body is oxidizing and corrading heavily during baking furnace, the reason is the hearth has no protective brick and the high air quantity and wind pressure.
济钢第二炼铁厂1#高炉大修后炉腹以下全部采用铝碳砖砌筑,烘炉时铝碳砖砌体发生严重的氧化侵蚀,分析其原因是炉缸未加保护砖、风量和风压过高等。
3.
For the reason, firstly the structure and technological conditions of furnace top, as well as the main characteristics of refractory concrete are described; then the aim, technological keys and measures of baking furnace are presented; finally in view of the existing problems in the course of baking furnace, the suggestions are given of strengthening techno.
分析耐火混凝土的主要性能 ,阐述烘炉的目的、要求 ,提出烘炉的关键技术与措施 ,指出烘炉过程中存在的问题。
5) heating-up
烘炉
1.
Heating-up of No.4 Hot Stove for #2 BF;
二高炉4号热风炉烘炉实践
2.
The success of heating-up hot stove was achieved by reasonable heating-up curve.
长钢8号高炉砖热风炉根据长钢实际情况,制定合理的烘炉曲线,顺利达到烘炉目的,为高炉的烘炉和开炉提供有力保障,实践证明,硅砖的快速烘炉是可靠的。
3.
The procedures of heating-up and starting-up a stamp-charging coke oven which burns solid fuel at low temperature are described.
介绍低温环境下捣固焦炉采用固体燃料烘炉和开工所采取的一系列特殊措施。
6) drying oven
烘炉
1.
,Ltd and details the reformation method of lining body of coke over and briefly explicates the design improvement from some ways of coke oven equipment,drying oven method,instrument and automation control process,etc.
介绍了莱钢焦化厂 3#焦炉的设计 ,详细阐述了焦炉砌体的改进 ,并简要说明焦炉设备、烘炉方法、仪表与自动化控制等几个方面的设计改
2.
The drying oven neasure of refractory for CFB boiler are introduced,and some demands in operational process are offered.
5万流化床锅炉为例 ,介绍了流化床锅炉耐磨耐火材料的烘炉方案措施及实施过程中具体要
补充资料：烘炉
分子式：
CAS号：
性质：涂膜在加热干燥过程中的加热设备，或称烘干室。不同型式烘炉有不同的结构和加热方式。按照其外形结构可分为箱式(烘箱)、室式(烘房)、通过式(又分直通式和桥式)。箱式和室式适用于单件或小批量生产。通过式适用于大批量的流水作业线生产，被涂物置于传送装置上，以一定的速度通过隧道式的干燥室。
CAS号：
性质：涂膜在加热干燥过程中的加热设备，或称烘干室。不同型式烘炉有不同的结构和加热方式。按照其外形结构可分为箱式(烘箱)、室式(烘房)、通过式(又分直通式和桥式)。箱式和室式适用于单件或小批量生产。通过式适用于大批量的流水作业线生产，被涂物置于传送装置上，以一定的速度通过隧道式的干燥室。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条