1) turbine floor
水轮机层
2) turbine gallery
水轮机廊道，水轮机层
3) turbine runner
水轮机转轮
1.
The cavitation-resistance puddle welding technique for turbine runner treatment and its benefit analysis;
水轮机转轮抗气蚀堆焊工艺及效益分析
2.
Aimed at a capacity-enlarging remodeling of the turbine runner of hydropower station in Xinjiang and based on the application of 3-D turbulent flow computation with k-ε model, the governing equations of turbulent flow in body -fitted coordinate systems for Francis turbine runner are presented.
针对新疆某电站水轮机转轮增容改造 ,基于 k-ε模型的全三维湍流计算技术在流动计算中的应用 ,给出了混流式转轮在贴体坐标系下的湍流计算的基本方程组 。
3.
The turbine runner of Bailong hydropower station was damaged in the fifth year of production,which caused the excessive amplitude of vibration and served no good for effective production.
百龙电站水轮机转轮投产不足5年就严重损坏,致使发电机组振动幅度大增,效率明显下降。
4) hydraulic turbine runner
水轮机转轮
1.
Computer simulation of turbulent flow through a Francis hydraulic turbine runner;
混流式水轮机转轮紊流流场的计算机仿真
2.
TBM-6 type blade shape measure Instrument for hydraulic turbine runner and its application were introduced in this paper.
本文介绍了TBM-6型水轮机转轮叶型测绘仪及其应用情况。
3.
The necessity and feasibility of redesign of hydraulic turbine runners in middle small sized hydropower stations are analyzed.
中小型水电站技术改造是水电事业发展的重要组成部分 ,本文通过对我国中小型水电站发展现状的论述 ,分析了在中小型水电站技术改造中水轮机转轮改型设计的必要性和可行性 ,并介绍了当前水轮机转轮设计、测试和制造方面的新技术。
5) hydraulic turbine
水轮机转轮
1.
Based on the compare of various traditional procedures,and with theory research and practice,the article put for wad a viewpoint and a procedure that the crack fixing of hydraulic turbine can be done without heat treat-ment in ex amine and repair of hydraulic plant.
通过对水轮机转轮裂纹修复几种传统工艺比较分析,针对水电厂检修特点提出了可采用不热处理进行修复的观点,并在理论研究和实际应用的基础上,较系统地提出了一套转轮裂纹修复工艺措施。
6) hydroturbine runner
水轮机转轮
1.
Experiment research on residual stress distribution in welding zons of large hydroturbine runners before and after anneal
大型水轮机转轮焊接区退火前后残余应力分布规律的实验研究
2.
The Longtan runners are the earliest super-large hydroturbine runners manufactured in construction site in China.
龙滩水电站水轮机转轮是国内最早在工地制造的大型水轮机转轮之一,文章详细介绍了龙滩转轮工地制造的质量标准、制造检验及验收程序,并对龙滩已交货的转轮主要质量指标以及整体质量进行评价,最后对工地制造转轮提出合理建议,对大型转轮工地制造及检验有一定指导和借鉴意义。
补充资料：水轮机层
水轮机层
turbine floor
shu一}日nJ{eerlg水轮机层(turbine floor)水轮机蜗壳顶板至发电机层楼板之间的楼层。立轴机组的水轮机层中部为机组及机墩，其周围布t有操作导叶的接力器、发电机引出母线、中性点、油水气管道及电缆等。当发电机支承结构为矮机墩时，则发电机定子、转子、下机架都落在水轮机层内。水轮机层地面一般多采用水泥抹面，也有的采用水磨石。地面上常设有电缆沟、管道沟，一般加有盖板以方便交通. 水轮机层的高度与发电机尺寸和布t有关，一般要满足发电机引出母线及设备布置需要，还要考虑人行交通和设备搬运，大型机组从水轮机层地面至发电机层之间高度较大，有的增加中间夹层。 横轴机组的水轮机和发电机装里在同一层，其下面为水轮机的泄水结构.灯泡贯流式机组，其发电机和水轮机都装里在下部过水管道内。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条