1) formwork
[英]['fɔ:mwə:k] [美]['fɔrm,wɚk]
模板;模架
2) formwork support
模板支架
1.
Design and construction for formwork support of high suspended structure at the top of cylinder;
仓筒顶部高空悬托结构模板支架设计与施工
2.
The design calculation of formwork support and scaffold at the construction site is controlled by structure stability and belongs to structural mechanics which is rather difficult to calculate.
建筑施工现场常用的模板支架与脚手架的设计计算是由结构稳定控制的,是理论性很强、分析计算很难的结构力学领域。
3) supported mode
桁架模板
1.
The author studies the structure design and structure checking calculation of Jintang large Bridge non-navigable span cast-in-place pier body template,emphasis on marine non-sport supported mode construction technology under the harsh ocean condition of wind,wave and flow,which has important significance on cast-in-place pier body construction under harsh environment.
研究了金塘大桥非通航孔桥现浇墩身模板的结构设计与结构验算,重点介绍了在恶劣的风、浪、流的海况条件下,海上无支架桁架模板施工技术,对恶劣环境下现浇墩身施工具有重要意义。
4) form support
模板支架
1.
The pitching scheme for the large-span form support in a certain project is analyzed,the bearing capacity of the whole system and the settlement value of the support are calculated,and the whole supporting system is verified combined with accumulated preloading test.
对某大跨度模板支架搭设方案进行设计分析,计算整个体系的承载能力及支架沉降数值,并结合实际的预压堆载试验对整个支撑体系进行分析验证。
5) falsework
['fɔ:lswə:k]
模板支架
1.
According to the principle of "geometric invariable bar system structure",a stable design is conducted for a practical falsework system supporting the up-structure of a bridge.
从工程实际出发,分析了目前在模板支架稳定性计算方面存在的问题。
2.
In domestic construction market, fastener-style steel pipe falsework have been wi.
在国内所使用的模板支架中,由钢扣件和钢管组成的模板支架由于构造简单、通用性强、使用成本相对较低、安全性较好等原因得到广泛应用,但与此相关的混凝土模板支架坍塌事故也时有发生,这已成为困扰目前建筑业的一大难题。
6) plated grillage model
板架模型
1.
The hull structure is simplified in the form of a plated grillage model.
基于非接触空爆理论,对作用于船体结构的载荷进行了分析,并将船体结构简化为板架模型进行了破坏作用的数值计算,计算结果与实际情况相符。
补充资料：Z-型支架
Z-型支架
介入放射学器材。Z-型支架属自胀式支架。包括Gianturco-Z-型支架，改良型Gianturco-Rosch 支架，螺旋型Z-支架，可回收式Z-支架。Gianturco-Z支架系不锈钢丝弯成Z形，然后围成圆柱状。支架的直径、长度可以根据需要而制造。一般钢丝的直径0.25～0.5mm，支架体的长度10～35mm，支架的直径5～30mm。制作工艺比较简单。缺点是单体支架容易移位，多体连接支架连接部的张力不够均匀。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条