1) warped blade
翘曲叶片
2) wafer warping
圆片翘曲
1.
When wafers in 150mm,200mm,or even 300mm are grinded to less than 150μm,the problem of wafer warping and edge damage becomes very obvious.
随着微电子工业迅猛发展,圆片直径越来越大,当150mm、200mm甚至300mm英寸圆片被减薄到150μm以下时,圆片翘曲和边缘损伤问题变得尤为突出。
3) warped plate
变形板，翘曲盘[片]
4) double sheet metal style warp
双金属片式翘曲
1.
Aiming at temperature excursion in test,the double sheet metal style warp is approved to be the main factor by analysis,experiment and simulation.
变栅距光栅线位移传感器工程样机完成后,进行了常态性能试验及环境试验,针对试验中出现的温度漂移问题,通过理论分析、试验验证、软件仿真,证实光栅组件的双金属片式翘曲为产生温漂问题的主要原因,并利用ANSYS-Workbench模拟得到解决方案,通过改进后的筒状腔体结构,使得温漂量值从12nm降到2nm以内。
5) bowed blade
弯曲叶片
1.
Correctly selected bowed blade can reduce the energy loss and improve the corner flow.
结果表明,优化的弯角和弯高范围随叶型折转角的增大而减小,合理选择弯曲方案将可以达到改善角区流动、减小损失的目的;叶片弯曲优化匹配设计可扩展现代压气机中弯曲叶片的应用范围,也表明了在大转角压气机中采用弯曲叶片设计方法的巨大潜力。
2.
It is pointed out that the positively bowed blade under the low Reynolds number condition is a good choice from the view of losses reduction and efficiency improvement according to the field analyzing for the different bowed blades under the low Reynolds number condition.
通过对不同弯曲叶片在低雷诺数条件下的流场分析,指出了在低雷诺数条件下正弯叶片仍是一种较好的降低损失的有效手段,并且在低雷诺数条件下正弯叶片的采用比在高雷诺数条件下所带来的收益更大。
3.
The exit flow fields of cascades with straight and positively bowed blades, with bowing angles of +10°，+20° and +30°, respectively，are measured by using a micro-five-hole probe.
通过采用微型５孔探针测量了常规直叶栅和端部周向倾斜角分别为１０°、 ２０°、 ３０°的正弯曲叶片叶栅的出口流场。
6) twisted blade
扭曲叶片
1.
The development and application of solid turbine technique and twisted blade technique are analyzedin this paper,And then the prospect of solid turbine with ring and twisted blades is also discusse
分析了整体涡轮盘技术和扭曲叶片技术的发展和应用，并讨论了带叶冠扭曲叶片整体涡轮盘技术的应用前景。
2.
The twisted blade as an important component of the centrifugal pump,the manufacture process and the precision are importamt factors in quality of centrifugal pump.
扭曲叶片作为离心泵的重要部件,它的制作过程及其精确程度都是影响离心泵质量的重要因素。
补充资料：双金
1."双南金"的略语。优质黄金。 2.喻指优秀的两篇诗文或两个人。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条