说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 机具布置
1)  tool arrangement
机具布置
2)  layout of furniture
家具布置
1.
From cutting space,application of partition,color,layout of furniture,it introduces the enlarging methods of small space,discusses small space surviving methods from enlarging method of small sitting room,changes of small kitchen and rebuilding of small balcony,in order to make the decoration of small house comfortable,functional,economical and artistic.
从切割空间、巧用隔断、妙用色彩、家具布置几方面介绍了小空间扩大法,并从小客厅"增容"法、小厨房变身术、小阳台改造几个方面论述了小空间求生术,从而使小居室的装饰设计既舒适又具有功能性、经济性及艺术性。
3)  Cutter layout
刀具布置
1.
A cutter layout method of the full-face rock TBM was proposed,in which the technological requirements of the cutter layout were summarized,then the rock-broken volume estimation method for the non-equality cutter space was given and a nonlinear multi-objective cutter layout mathematical model with complex constraints was established.
给出了全断面岩石掘进机的刀具布置设计方法,归纳出刀具布置的技术要求,并给出刀盘上不等刀间距的盘刀破岩量的估算方法。
4)  arrangement of illumination lamps
灯具布置
1.
Lighting design standard,arrangement of illumination lamps,illumination level calculation,illumination power supply and control design of gymnasium was introduced.
本文介绍了体育场照明设计标准、照明灯具布置方式、照度计算及照明配电与控制设计。
5)  rigging plan
索具布置图
6)  collocation of the machinery group
机具配置
1.
Mechanization is a complicated system engineering, and the mechanization system needs rational collocation of the machinery group and modern management technology, and the delay of any tache could affect the working efficiency of whole system.
机械化是一项复杂的系统工程 ,机械化系统需要合理的机具配置和高质量的现代管理 ,各个环节都影响整个系统的工作效率。
补充资料:ANSYS SOLID65环向布置钢筋的例子

 ANSYS SOLID65环向布置钢筋的例子
! 一个管道,环向配筋率为1%,纵向配筋率为0.5%,径向配筋率为0.1%
! 作者: 陆新征 清华大学土木系
!
FINISH
/CLEAR


/PREP7
!*
! 单元属性
ET,1,SOLID65
!*
KEYOPT,1,1,0
KEYOPT,1,5,0
KEYOPT,1,6,0
KEYOPT,1,7,1
!*
!实参数1:不同方向配筋
R,1,2,.001, , ,2, .01,
RMORE, 90, ,2,.005 ,90 ,90 ,


!材料属性
!混凝土基本材料属性
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,30E2
MPDATA,PRXY,1,,.2
!屈服准则
TB,MISO,1,1,5,
TBTEMP,0
TBPT,,0.0005,15
TBPT,,0.001,21
TBPT,,0.0015,24
TBPT,,0.002,27
TBPT,,0.003,24
!破坏准则
TB,CONC,1,1,9,
TBTEMP,0
TBDATA,,.5,.9,3,30,,
TBDATA,,,,1,,,
MPTEMP,,,,,,,,
MPTEMP,1,0
!钢材基本属性
MPDATA,EX,2,,200E3
MPDATA,PRXY,2,,.27
!屈服准则
TB,BISO,2,1,2,
TBTEMP,0
TBDATA,,310,2E3,,,,


! 管道内径和外径
CYL4,0,0,3000, , , ,10000
CYL4,0,0,2000, , , ,10000
VSBV, 1, 2


! 定义局部柱坐标
CSWPLA,11,1,1,1,
KWPAVE, 11
WPRO,,-90.000000,
VSBW, 3
WPCSYS,-1,0
KWPAVE, 1
WPRO,,,-90.000000
VSBW,ALL


ESIZE,500,0,
! 注意:设定单元局部坐标
VATT, 1, 1, 1, 11
!*
VSWEEP,ALL
/DEVICE,VECTOR,1
/ESHAPE,1.0
/REPLO
! 注意:红色代表最大配筋方向,绿色代表其次,蓝色表示最小配筋方向

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条