1) bushing set
衬套组
2) used sleeve assembly
旧衬套组件
3) seal and bushing group
密封和衬套组件
4) bush
[英][bʊʃ] [美][buʃ]
衬套
1.
Influence of the seal ring s compressibility within gear pump on the bush s static balance;
齿轮泵密封圈压缩量对衬套静力平衡的影响
2.
FEA for a double-helix single screw pump bush profile;
双头单螺杆泵衬套型线分析
3.
The deformation, stress and strain's distribution of the double-helix single screw pump bush are discussed when the bush is under equal pressure, disordered pressure and the static contact with the bush and screw.
用ANSYS对双头单螺杆泵衬套的受力情况作了有限元计算,为了提高计算效率,将螺杆泵衬套的有限元模型简化为平面应变模型求解。
5) liner
[英]['laɪnə(r)] [美]['laɪnɚ]
衬套
1.
Analysis and application of liner burning and rotary liner mechanism of connected bar;
连杆衬套烧研、转套机理分析与应用
6) Bushing
[英]['buʃiŋ] [美]['bʊʃɪŋ]
衬套
1.
Discussion About Wall Thickness Tolerance and Wall Thickness Difference of Bushing;
小议衬套壁厚公差与壁厚差
2.
Interference Fit of Bushing and Hole by Using Cold Extrusion;
用冷挤压法实现衬套与孔的干涉配合
3.
Fractures occurr frequently in the bushing made from high speed tool steel on the bearing system of blast hole rock bits A big increase in toughness is obtained through low temperature quenching and parameter optimization The industrial test shows that the fracture rate declines from 90%~96% by 7%~13% and drilling meters increase by 17%.
用高速钢制作矿用牙轮钻头轴承系统的衬套 ,普遍存在破裂现象 ,通过采用低温淬火和优化工艺参数 ,其韧性大幅度提高 ,工业试验的破裂率由传统的 90 %～ 96 %下降到 7%～ 13 % ,钻头穿孔米道提高了 17%。
补充资料：旋塞衬套
分子式：
CAS号：
性质：用石棉橡胶板冲切成一定形状，再涂以胶黏剂相互贴合、经模压硫化而制成的筒状密封制品。此产品耐热性好，强度高；启闭灵活，塞杆不易磨损，拆装方便。主要用于锅炉水位器旋塞，无眼衬套主要用于渗透性强的联苯及联苯醚混合物的反应釜及管道中。
CAS号：
性质：用石棉橡胶板冲切成一定形状，再涂以胶黏剂相互贴合、经模压硫化而制成的筒状密封制品。此产品耐热性好，强度高；启闭灵活，塞杆不易磨损，拆装方便。主要用于锅炉水位器旋塞，无眼衬套主要用于渗透性强的联苯及联苯醚混合物的反应釜及管道中。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条