1) Dipcoat
['dipkəut]
浸涂，浸覆
2) hot dip coating
热浸渍涂覆
3) dip coating
浸涂
1.
The seeds are introduced by polishing directly or dip coating.
分别利用打磨法和浸涂法在载体管上引入晶种 ,然后 170℃水热晶化 ,成功地合成了ZSM 5沸石膜 。
2.
Amorphous conducting V_2O-5 coatings were deposited on soda lime glass slides by dip coating from the hydrolysed VO(OC_2H-5)_3.
将玻璃在其乙醇溶液中浸涂、热处理后,得到表面无定形V_2O_5导电膜。
4) dip-coating
浸涂
1.
Bi2Sr2Ca1Cu2Ox (Bi–2212) thick films on Ag wires were prepared by using the dip-coating method.
通过浸涂法在银圆线表面制备了Bi2Sr2Ca1Cu2Ox(Bi–2212)超导厚膜。
2.
Gelatin films were prepared by dip-coating technology.
用浸涂的方法制备了明胶膜,测定了膜的机械性能、溶胀性能、对水的敏感性以及膜的含水量,并探讨了涂布温度、成膜液的pH、增塑剂甘油的添加量、交联剂的种类及添加量以及贮存环境湿度对明胶膜性能的影响。
5) dipping
[英][dip] [美][dɪp]
浸涂
1.
The waterborne epoxy/polyester dipping paint has excellent storage stability and corrosion protection and can applied in various industries The dipping process,application properties,technical specifications,cautions during application and tank content ratio and its adjustion have been describe
环氧聚酯水性浸涂漆具有优良的贮存稳定性、防腐蚀性及广泛施工适应性等特点。
2.
This article has reviewed the dipping process of water soluble epoxy ester paint for automobile chassis and design of production lines The application parameters, management, paint film performance and further improvement were also discusse
文章较系统地介绍了汽车底盘用黑色水溶性环氧酯浸涂漆涂装线布置设计及工艺。
3.
The horizontal rubber spreading machine for producing coated fabric in rubber sealing article was reformed from two-step coating tO One-step dipping process.
对原卧式涂胶机进行了改造，使２次刮涂工艺变为１次浸涂工艺。
6) coating
[英]['kəʊtɪŋ] [美]['kotɪŋ]
浸涂
1.
In this paper, the edible composite films were made from pullulan, sodium alginate and sodium carboxymethylcellulose by dip coating.
本课题以普鲁兰多糖,海藻酸钠和CMC为成膜材料,采用浸涂法制备可食用复合膜。
补充资料：浸涂
分子式：
CAS号：
性质： (一)一种用浸渍达到涂装目的的施工方法。其操作是将被涂物全部浸没在漆液中，待各部位都沾上漆液后将被涂物提起离开漆液，自然或强制地使多余的漆液滴回到漆槽内，经干燥后在被涂物表面形成涂膜。手工浸涂用于间歇式小批量生产；机械浸涂用于连续式批量生产的流水线上。该法只能用于颜色一致的涂装，不能套色，且被涂物上下部的涂膜厚薄不均匀，溶剂挥发量大，易污染环境，涂料的损耗率也较大。(二)橡胶加工中，浸涂工艺是用浸胶的槽，将织物布料浸挂上一层较浓较厚的溶剂胶浆，以代替用涂胶机涂胶的工艺。
CAS号：
性质： (一)一种用浸渍达到涂装目的的施工方法。其操作是将被涂物全部浸没在漆液中，待各部位都沾上漆液后将被涂物提起离开漆液，自然或强制地使多余的漆液滴回到漆槽内，经干燥后在被涂物表面形成涂膜。手工浸涂用于间歇式小批量生产；机械浸涂用于连续式批量生产的流水线上。该法只能用于颜色一致的涂装，不能套色，且被涂物上下部的涂膜厚薄不均匀，溶剂挥发量大，易污染环境，涂料的损耗率也较大。(二)橡胶加工中，浸涂工艺是用浸胶的槽，将织物布料浸挂上一层较浓较厚的溶剂胶浆，以代替用涂胶机涂胶的工艺。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条