1) plated beam
叠板梁
2) laminated plate-girder
叠合式板梁
3) laminated beam
叠梁
1.
Erection method of laminated beams of boiler structure;
锅炉构架叠梁的安装工艺
2.
Theoretical analysis and experimental research of laminated beam
叠梁理论分析与试验研究
3.
In order to accurately analyze the differences on load carrying ability among laminated beam,laminated beam with wedges and beam as a whole of the same dimension,this paper sets up a model of flection of laminated beams with rectangular cross section by taking advantage of Winkle s foundation assumption method and electric testing technique.
为了精确分析叠梁、加楔块叠梁和整梁的承载能力,采用温克尔假设法和电测实验技术,完成了矩形截面叠梁受力弯曲时的模型简化理论计算与实测分析。
4) stack
[英][stæk] [美][stæk]
板叠
1.
Based on the analysis of axial and transverse heat transfer characteristics,the performances of brass is compared with the stainless steel screen stacks Contrastive experiment with brass and stainless steel screen stacks in the pulse tube refrigerator thermoacoustically driven are carried out Experimental results are give
综合轴向和横向传热特性 ,比较分析了黄铜和不锈钢丝网板叠的性能 ,并采用黄铜和不锈钢两种丝网板叠进行了热声驱动脉管制冷的对比实验 ,给出了详细的实验结果和讨论。
2.
The onset behaviour of thermoacoustic osillation with various heat source temperatures was simulated,and the time responses of the temperatures at both ends of stack were also investigated numerically.
对不同热源温度的热声振荡起振特性进行了模拟,同时也数值模拟研究了板叠两端温度随时间的响应过程。
3.
In addition| the effects of stack structure and material property on the performance of the thermo-acoustic engine in terms of the critical temperature ratio were examined.
通过实验,揭示了热声自激振动与热声强制振动现象发生的条件与机理,研究了热声发动机的关键部件——板叠的形状与材质对系统的起振温度的影响。
5) laminated beam
叠层梁
1.
Calculation formulas for stress of laminated beam under bending experiment
叠层梁弯曲实验的应力计算公式
2.
A composite laminated beam is considered to be in a state of plane stress,the analytical solutions of frequencies and modal functions of a composite orthogonal and anisotropic laminated beam with simply-supported boundary condition are obtained by elasticity theory.
用平面应力模型来模拟复合材料叠层梁,得到了正交各向异性叠层梁的频率和模态函数,并用间接模态叠加法(IMSM)求得了叠层梁的瞬态响应。
3.
Based on generalizing the structure characteristics of bridge asphalt pavement,the laminated beam model is developed as for bridge asphalt pavement.
在分析总结桥面铺装结构承载特性的基础上,提出采用叠层梁作为桥面沥青铺装层间应力计算的简化模型。
6) steel composite beam
钢叠合梁
1.
The rebuilding scheme fully considers the harmony of the whole bridge with the surrounding environment, meets the planned traffic function requirements and the relative technical standards, puts forward the design of the steel composite beam structure for the main bridge and the technical measures taken for the sunk shaft foundation treat.
该文在对广州市增埗大桥既有桥梁结构安全性评价的基础上,提出增埗大桥改造方案?脑旆桨赋浞挚悸亲芴逵?周围环境的协调,满足规划交通功能要求及相关技术标准,提出主桥钢叠合梁结构设计、旧桥沉井基础处理所采取的技术措施,着重分析设计的重点、难点,可供类似工程借鉴。
补充资料：叠合式模具
分子式：
CAS号：
性质：又称叠层模。本模具的型腔在二个分型面上，前后各一。与常规模具相比它的体积约大15％，产量可提高约80％。它能充分利用注塑机的锁模力，但对模具的维修要求较高。大批量生产扁平塑料件时用它可提高生产率，降低成本。
CAS号：
性质：又称叠层模。本模具的型腔在二个分型面上，前后各一。与常规模具相比它的体积约大15％，产量可提高约80％。它能充分利用注塑机的锁模力，但对模具的维修要求较高。大批量生产扁平塑料件时用它可提高生产率，降低成本。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条