1) particle shape factor
颗粒形状系数,颗粒形状因数
2) particle shape factor
颗粒形状系数
3) correcting coefficient of the granule shape
颗粒形状修正系数
1.
Based on the relation between the average stress of particulates and microscopic contact force of granule,the relation between stress and strain of the earth-rock mixture was put forward by introducing the correcting coefficient of the granule shape.
基于散粒体平均应力与颗粒微观接触力之间的关系,引入颗粒形状修正系数,得到土石混合料的三维应力-应变关系。
4) particle shape
颗粒形状
1.
Effect of particle shape on uniaxial ratcheting of SiC_P/6061Al composites and its microscopic plastic deformation characteristics;
颗粒形状对复合材料单轴棘轮行为及其细观塑性变形特征的影响
2.
Effect of particle shape on biaxial tests simulated by particle flow code
颗粒形状对颗粒流模拟双轴压缩试验的影响研究
3.
It was shown that the particle shape deposited on the copper substrate was very sensitive to the strain extent of substrate.
实验表明沉积在铜表面的铝颗粒形状与局域应力缓释有直接的联系。
5) grain shape
颗粒形状
1.
Effect of grain shape on incipient motion of non-uniform sediment;
泥沙颗粒形状对非均匀沙起动条件的影响
2.
The zinc powders are classified as ordinary,fine and ultra-fine according to the grain diameter and spherical,lamellar and irregular according to the grain shape.
分析了锌粉的粒径、颗粒形状、金属锌含量对机械镀锌层的影响。
3.
A formula was derived to calculate the dry density of uniform sand with a new method based on establishment of an analysis mode, and the effect of sand grain shape on the dry density of sediment was discussed by introduction of the form index.
指出泥沙颗粒形状对泥沙干密度有较大影响,即泥沙的粒径愈细,形状愈扁平或愈长圆,其干密度就愈小;反之干密度就愈大。
6) grain form factor
颗粒形状因素
补充资料:颗粒形状
颗粒形状
particle shape
ke!1 xingzhuang颗粒形状(partiele shape)一个顺粒的轮脚边界或表面上各点的图象及表面的细微结构。通常包括投影形状、均整度(即长、宽、厚之间的比例关系)、棱边状态(如圆棱、钝角棱及锯齿状棱等)、断面状况、外形轮廓(如曲面、平面等)、形状分布等。常用的定量描述参数如下:形状系数指颗粒形状与某种规整形状(如球形)不一致的程度。包括体积形状系数八 V_一_一,,_一‘.5、一..一__~(人一卡),表面形状系数人(人~若)与比表面积形 D产’~四产“一,、~门、ro DJ~~~.产、M、,、,~,,,人、。,,~。,、口,,、。一二‘士。、状系数尹(尹一乎)。D、V和S分别为颗粒的直径、体,F、刁、~r、r人’。一、”n一z礴月J尸甘””’户“J~阵、『下积与表面积。形状指数是表征颗粒外形自身特征的参数。主要有三轴径之比,称为均整度;长短径之比,称为长短度;短径与厚度之比,称为扁平度;长短度与扁平度之比,称为郑格(z ingg)指数。 此外,颗粒外接立方体体积与颗粒体积之比称为体积充满度。颗粒投影面积与最小外接矩形面积之比称为面积充满度。体积与颗粒相等的球的比表面积与颗粒比表面积之比称为真球形度。面积等于颗粒投影面积的圆的直径与颗粒投影图最小外接圆直径之比称为实用球形度。与颗粒投影面积相同的圆的周长与颗粒投影轮廓周长之比称为圆形度。粗糙度是指颗粒实际表面积和将表面看成光滑时的表面积之比。 颗粒的形状对粉料的流动性、充填性等粉料特性有较大影响。通常,用颗式破碎机,对辊破碎机及圆锥破碎机易得到多棱角颖粒,而用球磨机与筒磨机得到的顺粒更接近球形。用化学法或气相沉积法制备的超微颗粒也易接近球形。 (李楠)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条