说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 液压[封头]螺栓拉伸机
1)  hydraulic (closure) stud tensioner
液压[封头]螺栓拉伸机
2)  hydraulic stud tensioner
液压螺栓拉伸机
3)  fitted-on closure stud tensioner
配装的封头螺栓拉伸机
4)  hydraulic stud tensioner shield ring
液压螺栓拉伸机屏蔽环
5)  hydraulic tensile bolt
液压拉伸螺栓
6)  hydraulic bolt tensioning jack
液压螺栓拉伸器
1.
This paper briefly expounds the working principles of the hydraulic bolt tensioning jack, analyzes the features of the hydraulic bolt tensioning jack, and emphatically probes into the problems existing in its application and solving methods.
简述了液压螺栓拉伸器的工作原理,分析了液压螺栓拉伸器的特点,重点探讨了其使用中存在的问题及解决办法。
补充资料:齿轮轮齿渐开线、螺栓、弹簧autolsp源程序
 

一、齿轮轮齿渐开渐开线


(defun c:gear(/)
(
 setq
p0 (getpoint"输入齿轮中心p0: ")
m  (getreal"输入齿轮模数M: ")
z  (getint"输入齿轮齿数Z: ")
ha 1
c 0.25
a (/ pi 9)
ra(/ (* (+ z (+ ha ha)) m) 2)
rf(/ (* (- z (+ (+ ha ha) c)) m) 2)
r(/ ( * m z) 2)
rb ( * r (cos a))
ri rb
ang 0
g (polar p0 ang rb)
)
(command "circle" p0 ra)
(command "circle" p0 rf)
(command "circle" p0 r)
(command "line"  g)
 
(while (< ri ra)
(setq
ang ( + ang(/ pi 360))
ri ( / rb (cos ang))
cta ( - (/ (sin ang) (cos ang)) ang)
g(polar p0 cta ri)
)


(command g)
)
(command )
)



二、螺旋源程序


(defun errMsg (s)
  (if (/= s "function cancelled") (princ (strcat "\nError: " s)))
     ; 当命令执行时出现错误
  (setvar "cmdecho" ocmdold)                                      ; 例如用户按下了CTRL + C
  (setvar "osmode" osmold)
  (setq *error* olderr)   ; 恢复旧的错误处理
  (princ)
)


(defun c:3Dthread (/ radouter threadpitch threadlength threadangle
                   ptStart innerdiafactor radmid radinner ocmdold osmold 4H 5H 6H h6 g6)
   ;-------------------------------------------------------------------
   ; 获取公制外径大小、螺距总长
   ; 然后计算一系列几何点
   ; 并且关闭对象捕捉、命令回显
   ;-------------------------------------------------------------------
   (setq 4H (list 0.0015 0.002 0.002 0.0025 0.003 0.0035 0.004 0.005 0.006 0.007 0.008 0.009 0.010))  
   (setq 5H (list 0.002 0.0025 0.003 0.004 0.0045 0.0055 0.0065 0.0075 0.009 0.010 0.0115 0.0125 0.0135))  
   (setq 6H (list 0.003 0.004 0.0045 0.0055 0.0065 0.008 0.0095 0.011 0.0125 0.0145 0.016 0.018 0.020))  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条