1) error pulse
误差信号脉冲
2) error pulse
误差脉冲
3) error signal
误差信号
1.
Adaptive Back-Propagation algorithm with magnified error signals;
一种基于放大误差信号的自适应BP算法
2.
Back-propagation algorithm based on enlarging error signals;
基于放大误差信号的BP算法
3.
The algorithm utilizes the correlation of output error signal to adjust the step size,solves the inconsistency problem of misadjustment and convergence time,and allows more flexibility in using.
该算法利用误差信号的相关值去调节步长,解决了算法收敛时间与稳态误差间的矛盾,为实际应用提供了更大的灵活性。
4) Signal error
信号误差
1.
The numerical analysis of signal error for Gaussian beam was conducted using the signal expression under uniform intensity and nonuniform intensity.
利用傅里叶光学理论,给出了光强不均匀情况下曲率波前传感器的曲率信号解析式,并利用光强均匀和不均匀情况下的信号表达式对探测高斯光束时的信号误差进行了数值分析。
5) pulse signal
脉冲信号
1.
Experiment of correlation detection of weak laser pulse signals;
微弱激光脉冲信号的相关检测实验
2.
Portable pulse signal apparatus based on single-chip microprocessor
基于单片机的便携式脉冲信号参数测试仪
3.
Research of waveform design based on UWB pulse signal
超宽带脉冲信号的波形设计研究
6) impulse signal
脉冲信号
1.
When the running situation of a rotating machine becomes abnormal or a part of it does not work well,it usually generates a periodic vibration signal or a periodic acoustic signal,which generally are periodic impulse signals with relatively strong noise.
这些信号通常是具有较强噪声的周期性脉冲信号。
2.
The time domain electric field integral equation (TD-EFIE) in conjunction with the reciprocity principle is applied to synthesize the transmitting impulse signals on condition that the receiving signals have already been known.
分别以蝴蝶形天线和超宽带槽式天线为例,并将计算结果与已知接收脉冲信号进行了比较。
3.
The paper introduces a designed time domain antenna which can make the measuring electromagnetic impulse signal not distorted.
最后利用宽带示波器显示的测量信号的结果,通过此显示的信号能很容易的计算出需要测量的脉冲信号。
补充资料：【系统误差】(systematicerror)
【系统误差】(systematicerror)
亦称“恒定误差”。在同一条件下多次测量同一量时，误差的数值和符号保持不变，或在条件改变时，按某一确定的规律变化的误差。产生的主要原因：（1）分析方法不完善。如在重量分析中，由于沉淀的溶解和共沉淀现象等；在职滴定分析中，由于反应进行不完全和*等当点与滴定终点不符合等，均将系统地影响测定结果偏高或偏低。（2）仪器本身不够精确。如砝码重量、容量器皿刻度等。（3）试剂不纯。（4）操作者主观上带来的误差。如对滴定终点颜色的辨别不同等。为保证分析结果的准确度，对这类误差必须尽量减小以致消除。常采用标准试样和标准方法来进行校正，或由不同单位、不同人员测得的结果，进行对照和评价，从而得出校正系数以消除之。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条