1) axial magnetizing force
轴向磁化力
2) axial magnetic force
轴向磁力
1.
To overcome the shortcoming that the magnetic force of an axial magnetization PMB(permanent magnetic bearings) is usually small,a new construction of APAM(axial placement and axial magnetization) multi-annular-shaped PMB which can make good use of magnetic energy and has greater axial magnetic force was designed.
为了解决轴向磁化永磁轴承磁力偏小的问题,该文设计了能充分利用磁能、具有更大轴向磁力的轴向放置轴向磁化的多个永磁环轴承新结构。
2.
The calculation of the axial magnetic force of radial magnetization bi-barrel-shaped PMB is very complex,and there is no practical analytical model for such calculation.
为了解决径向磁化的双筒永磁轴承轴向磁力数值计算复杂及缺乏计算轴向磁力的工程化解析模型等问题,该文在分析磁筒气隙磁导的基础上,结合磁通连续性原理和稀土永磁材料特性,通过电磁场理论中的虚位移法得到了该型轴承工程化轴向磁力解析数学模型。
3) axial magnetization
轴向磁化
1.
Aiming at small magnetic force and the complexity of magnetic force numeral calculation for previous research of radial magnetic force model on APAM(axial placement and axial magnetization) bi-annular-shaped PMB(permanent magnetic bearings),the new construction of APAM multi-annular-shaped PMB was designed,which can make good use of magnetic energy and have greater radial magnetic force.
针对轴向放置的轴向磁化双环永磁轴承径向磁力偏小以及磁力数值计算复杂等问题,设计了能充分利用磁能、具有更大径向磁力的轴向放置的轴向磁化多环永磁轴承。
2.
To overcome the shortcoming that the magnetic force of an axial magnetization PMB(permanent magnetic bearings) is usually small,a new construction of APAM(axial placement and axial magnetization) multi-annular-shaped PMB which can make good use of magnetic energy and has greater axial magnetic force was designed.
为了解决轴向磁化永磁轴承磁力偏小的问题,该文设计了能充分利用磁能、具有更大轴向磁力的轴向放置轴向磁化的多个永磁环轴承新结构。
4) axial-magnetized
轴向磁化
1.
In order to study the influence on its performance of the size effect in designing axial-magnetized permanent magnet micromotor, the edge-based analysis,which was the finite element method,was adopted to simulate the torque of this kind of dual rotor motor.
在轴向磁化永磁电机设计中,为研究尺寸效应对其性能的影响,采用基于单元边的有限元方法对这种双转子电机的转矩进行了仿真计算,得出了轴向磁化永磁微电机定子线圈线宽和线间距均为50μm的最佳布线密度;分析了电机在结构、转矩和气隙磁场多方面因素共同限制下所能达到的最小尺寸,即精密机械意义上的能满足实际应用的最小电机直径为10 mm,厚4 mm,通以0。
2.
In order to study the impact on its performance of the size effect in designing axial-magnetized permanent magnet micromotor,the finite element method was adopted to simulate the magnetic field of this kind of dual rotor motor,and the flux density wave form in the airgap was distributed.
为研究尺寸效应对轴向磁化永磁电机性能的影响,采用有限元方法对双转子电机的磁场进行了仿真计算,得出了轴向磁化永磁电机转子的气隙磁密波形分布。
3.
To investigate the impact of size on its performance in designing an axial-magnetized permanent magnet micromotor,the edge-based finite element method is adopted to simulate the torque of this kind of dual rotor motor.
在轴向磁化永磁电机设计中,为研究尺寸效应对其性能的影响,采用基于单元边的有限元方法对这种双转子电机的转矩进行了仿真计算,得出了轴向磁化永磁微电机定子线圈线宽和线间距均为50μm的最佳布线密度,分析了电机在结构、转矩和气隙磁场多方面因素共同限制下所能达到的最小尺寸,即精密机械意义上的能满足实际应用的最小电机直径为10 mm,最小厚度为4 mm,通以0。
5) axial magnetic flux
轴向磁力线
1.
The vital problem of end losses and heating caused by axial magnetic flux usually encountered in the design of large turbine generators is being elucidated,together with a description of the stator end s structure and design fundamentals of a 1 000 MW generator as well as the thermodynamic model of the end s lamina sheets.
阐述了大型汽轮发电机设计的重要问题———轴向磁力线引起的端部损耗和发热。
6) Axial electromagnetic force
轴向电磁力
补充资料：单轴各向异性
单轴各向异性是磁晶各向异性的最简单形式，即自发磁化的稳定方向（或易磁化方向）平行于一特殊晶轴。如六方晶系钴的自发磁化方向平行于 C轴(见晶体结构)，这就表现出强的单轴各向异性。磁性材料的单轴各向异性值一般都低于其磁晶各向异性值，为103erg/cm3量级。磁性材料经磁场热处理或强的冷加工而产生的感生各向异性，都属于单轴各向异性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条