说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 钻;螺旋输送机
1)  auger [英]['ɔ:gə]  [美]['ɔgɚ]
钻;螺旋输送机
2)  screw conveyor
螺旋输送机
1.
Cause analysis of and improvement to cracked main shaft of PTA screw conveyor;
PTA螺旋输送机主轴断裂事故分析及改造
2.
Design of the hydraulic system of shield s screw conveyor;
盾构螺旋输送机液压系统设计
3)  screw conveyer
螺旋输送机
1.
Optimal design of screw conveyer in pulping plants based on genetic algorithm;
基于遗传算法的纸浆螺旋输送机优化设计
2.
Energy consumption, production adjustability of raw material lifting equipments: flight conveyer and screw conveyer usually used in concentrated fruit juice production are analyzed br.
为此,对浓缩果汁加工中常见的果蔬提升设备-刮板输送机和螺旋输送机的能耗、生产适应性等情况进行了初步的分析,认为两种提升设备各有利弊,选型时应根据原料特性、生产稳定性及能耗等因素综合判断。
4)  spiral conveyor
螺旋输送机
1.
The papers introduce the procedure about one spiral conveyor, which concludes designation, calculation, and its drawing device erection and adduction, the designation, and the calculation is focal among these that motioned above.
介绍了螺旋输送机的选型设计过程,其中包括设计计算、螺旋输送机及配套驱动装置的选用和螺旋输送机的安装与调整3大部分。
2.
Considering the major factor extension and distortion,this paper introduced an empirical value method to modify the cutting off dimensions of spiral conveyor leaf,avoided the too large of diameter of raw material.
对正圆柱螺旋面的计算法公式进行了探讨,分析了产生误差的原因;考虑到拉伸变形这一主要因素,介绍了1种经验取值的方法来修正螺旋输送机轴叶片的下料尺寸,避免了胚料直径偏大。
5)  spiral conveyer
螺旋输送机
1.
Parameter choice in design of spiral conveyer in brick and tile industry;
砖瓦工业螺旋输送机设计参数的选择
2.
Cause of fracture analysis for contact flange of spiral conveyer
螺旋输送机连接法兰断裂原因分析
3.
The structural faults of the reverse blow valve, the pulse valve and the spiral conveyer are the reasons of the high fault rate of the bag type dust collector in the BF's spraying pulverized coal system at Jigang.
由于反吹阀、脉动阀及螺旋输送机结构存在缺陷 ,造成济钢高炉喷煤系统的布袋收尘器故障率高。
6)  conveying worm
螺旋输送机,输送螺旋杆
补充资料:螺旋输送机
      利用转轴上的螺旋叶片,沿料槽输送粉粒状物料的连续输送机械。物料因受自身重力和槽壁摩擦力的作用,不随螺旋叶片一起旋转,在螺旋叶片推动下,沿料槽的轴向运动,达到输送的目的(见图)。螺旋叶片分实体式、带式、桨叶式和齿形式。实体式适用于流动性好、干燥的小颗粒或粉状物料;带式适用于块状或粘滞性物料;桨叶式和齿形式适用于易被挤紧的物料。物料的输送方向取决于螺旋的旋向(左、右旋)及轴的旋转方向。螺旋输送机主要技术参数为螺旋直径。
  
  
  螺旋输送机的特点是:结构简单、横截面尺寸小、密封性好、工作可靠、制造成本低,便于中间装料和卸料,输送方向可逆向,也可同时向相反两个方向输送。输送过程中还可对物料进行搅拌、混合、加热和冷却等作业。通过装卸闸门可调节物料流量。但不宜输送易变质的、粘性大的、易结块的及大块的物料。输送过程中物料易破碎,螺旋及料槽易磨损。单位功率较大。使用中要保持料槽的密封性及螺旋与料槽间有适当的间隙。
  
  垂直螺旋输送机适用于短距离垂直输送。可弯曲螺旋输送机的螺旋由挠性轴和合成橡胶叶片组成,易弯曲,可根据现场或工艺要求任意布置,进行空间输送。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条