说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 脉动弯曲应力
1)  pulsating bending stress
脉动弯曲应力
2)  Curved artery
弯曲动脉
3)  bending stress
弯曲应力
1.
Finite element analysis on the bending stress for roller spur bevel gear based on ANSYS;
基于ANSYS的滚齿直齿圆锥齿轮弯曲应力有限元分析
2.
Analysis of tooth root bending stress for spiral bevel gears;
弧齿锥齿轮齿根弯曲应力分析
3.
Calculation of bending stress of steel-concrete composite beam considering slippage effect;
考虑滑移效应的钢—混凝土组合梁弯曲应力计算
4)  bend stress
弯曲应力
1.
The article anaylses the skew arch roofing s bend stress under symmetry and unsymmetrical loads,calculates the skew arch roofing critical load under the symmetry and unsymmetrical loads,the result indicates the skew arch roofing s resistance,and stability are sufficient for its use.
分析了在对称和非对称载荷作用下斜拱型屋面弯曲应力,计算了在对称载荷和非对称载荷作用下斜拱型屋面临界载荷。
2.
This paper demonstrate the way how to measure and control D max -D min  of the pressure cylinder for its safe working,which is started with the circular additional bend stress which is caused by the non circularity of the pressure cylinder,then it points out a new method of controlling strength of the pressure cylinder.
从压力容器不圆度引起周向附加弯曲应力出发 ,推导出检测和控制不圆度值的方法 ,使其达到其安全工作的目的 ,为工业生产及检测部门提供依
3.
This paper points out a proplem in《Mechanial Design of Forestry Engirieer-ing》Writted by Fu Wenfan that formula in calculating the bend stress of the hook.
本文指出了傅文范等著《森林工程机械设计》(绞盘机)中涉及到的关于吊钩钩身弯曲应力公式存在的问题,并根据有关理论,提出比较符合实际的计算吊钩钩身弯曲应力的公式。
5)  bending stresses
弯曲应力
1.
Software Development on Finite Element Analysis for Bending Stresses of Transmission Gears;
变速器齿轮弯曲应力分析有限元软件的开发
2.
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
在材料拉伸和压缩试验期间,由于加力轴线与试样轴线不同轴产生弯曲应力,影响试验结果。
6)  flexual dynamic stress of double arced gear
双圆弧齿轮弯曲动应力
补充资料:锁骨下动脉-锁骨下动脉-颈动脉旁路术


锁骨下动脉-锁骨下动脉-颈动脉旁路术


适用于大动脉炎所致的左锁骨下动脉和左颈总动脉起始处缩窄、闭塞而无名动脉通畅者,无名动脉分叉处缩窄、闭塞而左锁骨下动脉通畅者。手术在全麻下取双侧颈部横切口。显示双侧锁骨下动脉,用0.7~0.8cm口径的人工血管,经胸锁乳突肌后方隧道,作人工血管与锁骨下动脉端-侧吻合。若颈总动脉起始处有缩窄、闭塞者,加作颈部垂直切口,显露颈总动脉,再以等粗人工血管与颈总动脉及移植于两锁骨下动脉间的人工血管分别作端-侧吻合。手术可纠正或改善脑部和左上肢的血液供应。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条