说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 侧压下量
1)  edging [英]['edʒɪŋ]  [美]['ɛdʒɪŋ]
侧压下量
2)  indirect rolling action
侧压下;轧制侧向压下
3)  increment of lateral pressure
侧压力增量
1.
By analyses of the results measured during construction of pile foundation,we have studied the quantity,distribution and range of the increment of lateral pressure in soil around the pile caused by installation of pile,and compared them with theoretical estimates.
通过对桩基施工过程中实测资料的分析,探讨了沉桩时单桩周围土中产生的侧压力增量的大小、分布规律及影响范围,并与理论解进行对比。
4)  reduction [英][rɪ'dʌkʃn]  [美][rɪ'dʌkʃən]
压下量
1.
Simulation on hot rolling compounding of two metal plates and determination of minimum relative reduction;
双金属板热轧复合模拟及最小相对压下量的确定
2.
Determination of minimum relative reduction in hot rollingcompounding of stainless and carbon steel plates;
不锈钢-碳钢板热轧复合最小相对压下量的确定
3.
Stress and strain analysis of H beam universal rolling in different flange reductions;
H型钢轧制翼缘不同压下量的应力应变分析
5)  stroke of pressing down
压下量
1.
A method of determining high precise stroke of pressing down of straightening drill pipe is presented.
对于这种专用的、尺寸大且要求校直精度高的管材 ,运用弹塑性理论建立了其压点式反弯校直数学模型 ,提出了一种精度较高的校直压下量的确定方法 。
2.
A practical computation method for the stroke of pressing down is derived, which can be used to direct the straightening operation.
给出了实用的确定矫直压下量参数的方法 ,从而为实际矫直工作提供了的理论指导 。
6)  press amount
下压量
1.
The principle of cutting and splitting glass substrates of TFT-LCD and the impacts of craft parameters on cutting quality, such as scribe-wheel angle, cut pressure, press amount are studied in this paper.
研究了TFT-LCD切割裂片的原理,以及刀轮角度、切割压力、下压量等工艺参数对切割质量的影响。
补充资料:锅炉、压力容器、压力管道及特种设备定期检验


锅炉、压力容器、压力管道及特种设备定期检验
periodic inspection of boilers, pressure vessels, pressure piping and special equipment

  guolu YOli侧飞扣1 YOli gLJal对印ji tez陌叩劝以拍1 dingqi】,on四n锅炉、压力容器、压力管道及特种设备定期检验(peri诫c inspectionof城le。,p~切reves-Sels,p~二piPing ands衅过闪uiplr屺nt)为保证设备的安全使用,规定设备必须按一定周期进行法定的、强制性的检验。定期检验由政府设立的检验所、使用单位或行业检验站进行。检验单位及检验人员必须具有与所检设备相适应的资格。设备使用单位应该建立定期检验制度,做好检验计划,按时向检验单位提出申请。检验单位应该保证及时进行检验,检验按有关检验规则进行。检验时,设备使用单位应做好配合工作,提供必要的运行资料。检验完毕,检验单位要出具检验报告,对设备能否使用,要作出明确结论。如设备有缺陷,要提出是否修理、监护使用和报废的处理意见。锅炉压力容器安全监察机构根据检验机构的报告,发使用许可证书。有缺陷的,责令使用单位修理,修理后检验仍不符合安全要求的,则通知报废。使用单位逾期不进行定期检验,锅炉压力容器安全监察机构有权停止其设备运行。(陈亦惠)
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条