1) tracking
[英][træk] [美][træk]
![点击朗读](/dictall/images/read.gif)
老化漏电
2) Leakage power minimization
![点击朗读](/dictall/images/read.gif)
漏电优化
3) dielectric aging
![点击朗读](/dictall/images/read.gif)
介电老化
1.
The dielectric aging of Pb(Zn1/3Nb2/3)O3-based ceramics with multiphase composite structure at 25℃ is studied as a function of sintering temperature and soaking time.
研究了Pb(Zn1/3Nb2/3)O3基复相陶瓷的室温介电老化行为与材料烧成制度的关系,发现介电常数与老化时间的对数值成线性关系,随烧成温度提高和保温时间延长,老化速率增大,老化速率对频率的依存性增加。
4) corona aging
![点击朗读](/dictall/images/read.gif)
电晕老化
1.
In this thesis, the effect of nitric acid on the performance of silicone rubber (SIR) material during corona aging was investigated.
本文主要开展了硝酸在硅橡胶材料电晕老化过程中的作用的研究。
5) electrical aging
![点击朗读](/dictall/images/read.gif)
电老化
1.
The effect of Free Radical Scavenger on space charge distribution in polytethylene during electrical aging;
自由基清除剂对电老化聚乙烯中空间电荷分布的影响
2.
In order to understand the physical mechanisms of partial discharge(PD) in insulation,the accelerated electrical aging tests of XLPE specimens were performed and an ultra-wideband(UWB) PD measurement system was adopted to study the characteristics and mechanisms of PD in XLPE during electrical aging.
为了研究绝缘中发生局部放电的物理机制,对交联聚乙烯(XLPE)绝缘试样进行了加速电老化试验,使用超宽频带局部放电检测系统(频带10 MHz~3 GHz)测量了试样的放电信号,并通过统计分析超宽频带放电的单次脉冲信号探讨了XLPE绝缘老化过程中的放电机理。
3.
During the tests of withstand voltage and electrical aging for large steam turbo-generator stator winding insulation, the flashover at the ends of stator bar and overheating of the corona- protective coating might take place, which would cause the winding insulation to burn out and the test not to continue .
大型汽轮发电机在主绝缘耐压和电老化试验中,可能出现定子线棒端部闪络和防晕层过热的情况,从而损伤主绝缘,影响试验顺利进行。
6) converter burn-in
![点击朗读](/dictall/images/read.gif)
电源老化
补充资料:电流型漏电保护
分子式:
CAS号:
性质:以反映漏电设备外壳对地电流为动作信号的保护方式。有剩余电流型和泄漏电流型两类,但一般所指都是前者。相应的装置称为电流型漏电保护装置。这种保护装置采用零序电流互感器作为取得触电或漏电信号的检测元件。这种保护装置既能防止间接接触电击,也能防止直接接触电击。纯电磁式剩余电流型漏电保护装置以极化电磁铁作为执行机构。其主要优点是使用元件少、可靠性较高、承受过电流或过电压冲击的能力较强、缺相时性能稳定;其不足之处是灵敏度不高、材料要求和工艺要求较高。电子式剩余电流型漏电保护装置以电子线路作为中间机构,以普通电磁铁或继电器作为执行机构。其主要优点是灵敏度高、动作准确、容易取得动作延时、动作电流和动作时间容易调节、容易设计出多功能的保护器、工艺比较简单;其不足之处是可靠性较低、抗过电流和过电压冲击的能力较弱。
CAS号:
性质:以反映漏电设备外壳对地电流为动作信号的保护方式。有剩余电流型和泄漏电流型两类,但一般所指都是前者。相应的装置称为电流型漏电保护装置。这种保护装置采用零序电流互感器作为取得触电或漏电信号的检测元件。这种保护装置既能防止间接接触电击,也能防止直接接触电击。纯电磁式剩余电流型漏电保护装置以极化电磁铁作为执行机构。其主要优点是使用元件少、可靠性较高、承受过电流或过电压冲击的能力较强、缺相时性能稳定;其不足之处是灵敏度不高、材料要求和工艺要求较高。电子式剩余电流型漏电保护装置以电子线路作为中间机构,以普通电磁铁或继电器作为执行机构。其主要优点是灵敏度高、动作准确、容易取得动作延时、动作电流和动作时间容易调节、容易设计出多功能的保护器、工艺比较简单;其不足之处是可靠性较低、抗过电流和过电压冲击的能力较弱。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条