说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 素点
1)  prime spot
素点
2)  Pixel Point
像素点
1.
This article researches on how to make the curve edge translated into a straight line,introduces the measure formula between the pixel point and the space point,describes image processing ideas,and proved that this method can get better results by experiment.
这篇文章研究了把图像的曲线边缘变为直线边缘的图像平视化处理方法,推导了像素点和空间点的对应关系公式,陈述了图像平视化处理的思路,并对现场采集的图像进行了平视化处理。
3)  prime periodic point
素周期点
1.
Condition of the continuous self-mapping of unit solid body in R~n with prime periodic points;
N维单位体上连续映射有素周期点的条件
2.
Nitecki indicate the equal value of the special abnormal point,abnormal point and prime periodic point,respectively.
N iteck i分别指出了有特殊异状点、有异状点、有素周期点三者等价。
3.
Nitecki indicates respectively the equalvalue of the spcial heterochinic,point,heterochinic point and prime periodic point.
Nitecki分别指出了有特殊异状点、有异状点、有素周期点三者等价。
4)  Pixel [英]['pɪksl]  [美]['pɪksəl]
像素点
1.
To automatically recognize the boundary spot and to record the coordinate in a clockwise direction are realized through the comparison of the value between the starting randomly boundary spot S and 8 pixels Pfi around S .
提出了一种能快速有序搜索边界点的新方法 ,通过比较任一起始边界点S与周边 8个像素点Pfi的值 ,实现按顺时针方向自动识别边界点并记录其坐标。
2.
It can be decided whether a pixel is in the region.
通过判断某一像素点是否在该区域中,若在则将其压栈,然后判断该像素点的相邻点是否也在该区域中,若某一像素点的相邻点均已处理过,则将其出栈,由累计压栈次数便可统计出该区域的面积。
5)  site variable
地点因素
1.
An understanding of influences of site variables on surface soil organic carbon(SOC)concentrationis i mportant to plan future land use for carbon sequestration and sustaining agriculturalproduction.
利用中国第二次土壤普查确定的886个典型地带性土种剖面资料,通过统计分析方法研究了地点因素(土纲、质地、海拔、酸碱度和土地利用方式)对地带性土壤表层有机碳含量的影响。
6)  Point Factors
点状因素
1.
Computer Assessment of Point Factors on Land Parcel Price Based on Shortest Path;
基于最短路径距离的宗地地价点状因素自动化评价
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条