说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 真振幅地震剖面
1)  true-amplitude seismic section
真振幅地震剖面
2)  amplitude section
振幅剖面
1.
Project the fault plane in vertical and horizontal directions to obtain the amplitude sections and amplit.
本文的做法是,先用三维地震垂直剖面和水平切片对断层进行闭合,然后将断层面作垂直和水平方向的投影,获得断层上、下盘的振幅剖面及振幅切片;再根据钻井资料及合成记录,对振幅剖面及振幅切片进行岩性解释,获得相应的岩性剖面和岩性切片。
3)  amplitude of ground motion
地面地震振动振幅
4)  seismic amplitude
地震振幅
5)  the amplitude ratio profile
振幅比剖面
1.
Through the processing and interpretation to seismic data of Zhungeer basin, the validity of using the amplitude ratio profile to identify the interface of stratum and lithology is verified, which has provided a valid auxiliary means for seism.
利用叠前Kirchhoff积分偏移,研究了一种有效的求取振幅比剖面的方法,分析了振幅比剖面随参数变化的规律,并探讨了振幅比剖面的地质解释。
6)  seismic profile
地震剖面
1.
Geological interpretation of the seismic profile in Tarim Basin and tectonic evolution of this area
塔里木盆地地震剖面地质解释及其构造演化
2.
Demarcating through-well seismic profile with diplog is one of the important ways to improve the quality of seismic interpretation.
地层倾角测井标定过井地震剖面是提高地震成果质量的重要途径之一。
3.
In seismic description,it often traced geologic horizon in seismic profile and reflected the geologic information on corresponding seismic horizon.
在地震解释中,常常在地震剖面上追踪地质层位,并且将地质信息映射到相应的地震层位上,有时追踪某一地震层位的波峰,有时是波谷,多数时候都没能精确地确定地质层位的位置。
补充资料:关于solidworks 中的剖面线中的剖面线

solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义.


方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn


用笔记本打开该文件,添加需要的线形.如


;; Based on AutoCAD Ver.13.0s Hatch Pattern File


;;;; solidworks 区域剖面线定义文件 ::


*金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry


45, 0,0, 0,.125


*塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation


45, 0,0, 0,.125


135, 0,0, 0,.125


*玻璃,AR-GLASS@1.0


45,0,0,0,0.5, 0.5,-0.5


45,0,0.1414214, 0,0.5, 0.3,-0.7


45,0.1414214,0, 0,0.5, 0.3,-0.7


*软木, Cork material@1.0


0, 0,0, 0,.125


135, .0625,-.0625, 0,.35355339, .176776696,-.176776696


135, .09375,-.0625, 0,.35355339, .176776696,-.176776696


135, .125,-.0625, 0,.35355339, .176776696,-.176776696


*无, None


删除不需要的定义类型,可以大大提高solidworks 的启动速度

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条