|
|
1) shore profile
海滨剖面
2) foreshore profile
前滨剖面
1.
Based on the repeatedly measured data including waves, currents, beach underwater tables and the foreshore profiles for every hour over several days in the Houjiang Bay of the eastern Guangdong coast, four significant canonical correlation variables, accounting for more than ninety percent of the total variance, were extracted by CCA.
利用在粤东后江湾多日逐时连续观测的近岸波浪、流、海滩潜水位和海滩前滨剖面地形数据,通过典型相关分析方法提取了占总方差90%以上的4个显著的典型相关变量,进而分别论述了常波况下海滩前滨剖面不同部位的地形动力过程。
3) beach profile
海滩剖面
1.
Based on the cutting-filling amplitudes of the beach profiles and the records of wave and tide,the repeatedly measured profile data on the beach between headlands at the Liaozuikou bay in Shanwei, Eastern Guangdong Province were analyzed by empirical orthogonal function.
结果表明 ,海滩的月内日变化过程可客观地通过对应于 2个最大特征值的 2个经验特征函数来描述 :1 )第 1经验特征函数表征主要的海滩剖面过程 ,称为主要模式 ,它是响应叠加在月潮汐周期性循环上的波浪动力作用 ;2 )第 2经验特征函数反映了海滩剖面快速变化过程 ,称为次要模式 ,它又可分为前滨上部过程、冲淤过渡段及后滨上部过程。
4) foreshore section
海滩剖面
1.
Based on the characters of seaside area,using the traditional surveying method,a way to survey the foreshore section is introduced.
结合传统水准测量的手段,介绍了一种海滩剖面监测的可行方案,并给出了数据处理方法,为威海核电厂工程的选址提供了参考。
2.
When discussing the feasibility of seaside projection,it is necessary to evaluate the eroding grade which can be reflected by the fluctuating of foreshore section line during one period.
海滩侵蚀是影响临海建筑物稳定性的不利因素,临海工程可行性论证中有必要对海滩侵蚀情况做出评估,通常可通过海滩剖面某一段时期内的变化来反映海滩侵蚀程度的强弱。
5) coastal profile
海岸剖面
1.
Based on the observed topographic data on 36 profiles in the Yellow River dalta littoral area and the observed hydrographic and sediment data at the Lijin Hydrologic Station,the dynamic geomorphology method is used to study the coastal profile forms and scour-deposition evloution of the Yellow River delta.
根据1976—2002年黄河三角洲滨海区36个断面的地形实测资料以及利津水文站的水沙资料,运用动力地貌学的方法,对黄河三角洲海岸剖面形态及冲淤演变进行了研究。
6) sea-bottom profile
海底剖面
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|