1) pressure contact welding
压力接触焊接
2) contact pressure
接触压力
1.
Calculation of contact pressure on TM and VAMACE premium connection casing couplings;
TM和VAMACE特殊螺纹套管接箍接触压力计算
2.
The effect of articular step-off and neniscectomy on joint alignment and contact pressures for fractures of the lateral tibial plateau;
胫骨外侧髁骨折塌陷对关节轴线及接触压力的影响
3.
Single chip microcomputer-based inspection of catenaries-pantograph contact pressure;
基于单片机的弓网接触压力检测
3) contacting pressure
接触压力
1.
Research on contacting pressure in ball-spinning;
滚珠旋压工艺中成形区接触压力的分析计算
2.
A pin-on-disk test rig was used to investigate the influence of sliding speed and contacting pressure on the friction and wear behavior of 45CrNi pair under dry sliding condition.
利用销盘摩擦磨损试验机,考察了干滑动摩擦条件下滑动速度、接触压力对45CrNi摩擦副摩擦磨损性能的影响。
3.
The progressive cavity pump(PCP) distortions,forces and contacting instance of different pressure with the finite element analysis method are analyzed,the PCP two-dimension finite element model is constituted,the stress distributing correspond to the PCP stator rubber and the contacting pressure of the stator and rotor are obtained in this paper.
用有限元方法对螺杆泵在不同压力作用下的变形、受力及接触情况进行了分析研究,建立了螺杆泵的二维有限元模型,得出了在相应情况下螺杆泵定子橡胶的应力分布和螺杆泵定子与转子的接触压力。
5) contact force
接触压力
1.
The improving of F-ECTS is composed of three parts: analyzing the major influence factor of fretting length precision; importing force sensor to monitor the dynamic change of contact force during fretting experiment and modification of current con
微动电接触测试系统的改进将包括三部分内容:一、分析影响微动行程精度的主要因素,并提出提高精度的方案;二、引入力传感器应对微动实验过程中接触压力的动态变化,并结合力传感器改进现有系统接触压力加载与保持结构的设计;分析“四点法”测试接触电阻的四线连接可靠性的影响因素,并改进接触电阻采集记录方式,减少数据冗余。
2.
Based on dynamic theory of roller bearing,considering variable real-time contact force and rotational velocity of roller bearing,a numerical simulation model of wearing for cylindrical roller bearing was established by the method for wear numerical simulation of components,and the wear lifetime of cylindrical roller bearing was predicted.
基于滚动轴承的动力学理论,考虑滚动轴承承受的接触压力和自转速度实时发生变化,依据零件磨损过程通用的数值仿真方法,建立了圆柱滚子轴承磨损的数值仿真模型,并对其磨损寿命进行了预测。
3.
Considering the contact forces and safety,the comparisons were made for the simulation results to select the suitable parameters for the overhead contact line system of high-speed railway.
考虑到接触压力和运行的安全性,对不同的动态仿真结果进行比较,据此选取合适的高速接触网参数。
6) welding pressure
焊接压力
1.
The effect factors of production operation on quality of welding pipe are consisted of inputting heat,welding pressure,welding speed,opening angle,seated position of inductor and resistor,geometry size and shape of roughing pipe and so on in the production process of high frequency welding pipe Holding operation process in the production is a important way for increasing the welding pipe qualit
高频焊管生产中 ,操作对焊管质量的影响因素包括输入热量、焊接压力、焊接速度、开口角、感应器和阻抗器的放置位置、管坯的几何尺寸及形状等几方面。
2.
Consequently it is difficult to optimize the welding pressure in pressure constant mode used in conventional ultrasonic plastic welder.
为此本文利用VEP3 1 2压力控制型电气比例阀在能量模式控制的超声焊机基础上 ,首次实现了压力在焊接过程中的可变调节 ,使得焊机能够优化焊接压力 ,从而为接头质量优化奠定了硬件基础。
补充资料：接触压力
分子式：
CAS号：
性质：胶接施工时，胶接件固化过程中不再另行施加其他压力，仅靠胶接件自身的质量所产生的压力。
CAS号：
性质：胶接施工时，胶接件固化过程中不再另行施加其他压力，仅靠胶接件自身的质量所产生的压力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条