1) initial throughput
初始输量
2) initial modulus
初始模量
1.
The impact of temperature and duration of heat treatment on the breaking strength,elongation at break,initial modulus and work to break of the fibers was investigated.
对玉米纤维进行不同方式的热处理实验,得出了热处理温度和热处理时间对断裂强度、断裂伸长、初始模量、断裂功的影响规律。
2.
The tensile strength and initial modulus were remarkably decreased and the breaking elongation and flexibility of grafted fiber were increased.
接枝后纤维强度和初始模量下降,断裂伸长和柔顺性提高;耐酸、耐碱能力随接枝率的增加而提高,热稳定性提高,回潮率下降。
3.
Results show that,crystalline,crystallite size, breaking strength and initial modulus of the fiber are all decreased after graft copolymerizations of MA.
分析讨论了纤维接枝后结晶度的变化情况,及结晶度与力学性能的关系,结果表明接枝MA后纤维的结晶度、晶粒度、断裂强度和初始模量均有下降。
3) initial production
初始产量
1.
Comparing three forecasting methods with individual well initial production,it is thought that the numerical simulation method could consider many factors and actual situation.
比较三种单井初始产量预测方法认为 ,数值模拟方法考虑了多种因素 ,符合油田实际。
4) initial discharge capacity
初始容量
1.
The results show that the nanophase LiCoO 2 performs poor initial discharge capacity,good cyclic stability and high discharge voltage.
5 % )加入普通LiCoO2 中得到的混合样初始容量有所提高 ,放电电压平台较高 ,循环稳定性更好 ,适合作为锂离子电池正极材料。
5) Initial capacity
初始容量
1.
Based on element analysis of electrolyte,ICP analysis,object phase analysis as well as comparison of initial capacities the results indicated that the SnSO 4 additive quantity in the electrolyte must be strictly controlled and both the initial capacity and cycle life can be improved if an optimum additive quantity is select.
为了研究硫酸亚锡在电动自行车VRLA电池中对初始容量、循环寿命的影响,笔者设计并配制了不同添加剂含量的电解液试制电池。
2.
Comparison tests were done for batteries made by different gel-filling technologies,and the results showed that all the filling methods had their own defects regardless of direct filling or acid replacement,but the difficulty of gel-filling could be mitigated and the initial capacity and cycle.
试验结果表明:直接灌入法、酸置换法均存在缺陷,而采用过放电法并配以合适的初充电工艺不但可以大大减小胶体灌注的难度,而且可以适当提高胶体蓄电池的初始容量及循环性能。
3.
It was shown that the particle size distribution of lead powder played an important role in plate porosity,initial capacity and cycle life of the battery.
结果表明 :铅粉粒径对极板的孔隙度、成品电池的初始容量、充电接受性和循环寿命有较大影响。
6) initial discharge
初始流量
1.
With the loop method and the conventional Hardy Cross method,the paper investigated the effect of different initial discharge distribution on the astringency.
在利用回路法和传统的Hardy Cross法对算例管网进行水力计算时,采用了不同的初始流量分配方案以研究其对收敛性的影响。
补充资料：刚性模量
分子式：
CAS号：
性质：又称切变模量或刚性模量。材料的力学性能指标之一。是材料在剪切应力作用下，在弹性变形比例极限范围内，切应力与切应变的比值。它表征材料抵抗切应变的能力。模量大，则表示材料的刚性强。剪切模量的倒数称为剪切柔量，是单位剪切力作用下发生切应变的量度，可表示材料剪切变形的难易程度。
CAS号：
性质：又称切变模量或刚性模量。材料的力学性能指标之一。是材料在剪切应力作用下，在弹性变形比例极限范围内，切应力与切应变的比值。它表征材料抵抗切应变的能力。模量大，则表示材料的刚性强。剪切模量的倒数称为剪切柔量，是单位剪切力作用下发生切应变的量度，可表示材料剪切变形的难易程度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条