1) HRC
洛氏硬度C
2) RC Rockwell Hardness C Scale
洛氏硬度C级
3) Rockwell hardness
洛氏硬度
1.
A Comparative Study of Impact Strength and Rockwell Hardness on Nano Composite Denture Base Resin and Traditional Denture Base Resin;
纳米基托复合树脂与传统基托树脂冲击强度及洛氏硬度的对比研究
2.
The Evaluation of Measurement Uncertainty for Rockwell Hardness (Scale A) Test of Cemented Carbide
硬质合金洛氏硬度(A标尺)测量不确定度的评定
3.
The grain size is increa seda little and Rockwell hardness is decreased a little by solid solution treatment at the temperature below grain coarsening temperature(1150 ℃) due to undissolved carbo-(nitride),but grain grow rapidly and Rockwell hardness de.
结果表明,弥散分布的碳氮化物对晶粒长大有显著阻碍作用,在低于该钢的晶粒粗化温度(1 150℃)固溶处理时,大量未溶解的碳氮化物使得晶粒尺寸增幅较小、洛氏硬度小幅下降;在高于1 150℃时,随温度的升高或时间延长,晶粒长大迅速,洛氏硬度大幅下降;晶粒生长指数随固溶温度的升高而呈台阶式增长;在固溶温度为1 050~1 100℃下的晶粒长大激活能为189。
5) Rockwell hardness tester
洛氏硬度计
1.
Using the cone anvil made by self, inspect the hardness of small steel ball on WELSON - A653T Rockwell hardness tester ,solve the problem of the small steel ball is slip on the pedestal anvil and "V" shape anvil, difficult to fix,and make the variance analysis to the result compare with traditional method,and to prove the result , of inspect by this way is correct.
在WELSON—A653T洛氏硬度计上,采用自制凹锥形砧座测试微小钢球的硬度,解决了微小钢球在常用平面砧座和V形砧座上易打滑,不易固定,致使压头打在砧座上,损坏压头和砧座的难题,并采用方差分析的方法,将该法与传统试验方法相比较,验证其检测结果与传统法所获检验结果无显著性差异。
2.
The Rockwell hardness tester is a precision measurement instrument in material and part hardness testing, which is often used in detection of materials, product and half-finished product.
洛氏硬度计是检测材料和零件硬度较精密的计量仪器,用来测量材料或者成品半成品的相应硬度,其性能指标主要体现在检测精度和操控性两个方面。
3.
The text particular introduced working principle of Rockwell hardness tester, designed load-up program, analyzed raliability,and according related requirements elected electromechanical and the like components.
传统洛氏硬度计采用杠杆加载,压头多在侧向用紧定螺钉顶紧,长期使用很难保证精度,且需要操作人员的经验和技巧。
6) Rockwell hardness number
洛氏硬度数
补充资料：洛氏硬度
分子式：
CAS号：
性质：又称罗氏硬度。表示材料硬度。一种标准。用符号HR表示。应用压入法把压力施加在金刚钻尖上，使压入所试材料的表面而产生凹痕。用测得的凹痕深度来表示硬度。标度数越大，硬度越小。用于测定塑料、绝缘材料和金属材料等的硬度。
CAS号：
性质：又称罗氏硬度。表示材料硬度。一种标准。用符号HR表示。应用压入法把压力施加在金刚钻尖上，使压入所试材料的表面而产生凹痕。用测得的凹痕深度来表示硬度。标度数越大，硬度越小。用于测定塑料、绝缘材料和金属材料等的硬度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条