2) equivalent moment of inertia constraint conditions
等惯量约束条件
1.
The impact proof mass on the gyros performance is discussed on the basis of microgyro dynamic equation and several important parameters in the design of micromechanical vibrating gyros, including equivalent moment of inertia constraint conditions in the inner and outer gimbals, sensitivity, etc .
根据陀螺的动力学方程，从陀螺设计中的重要参数——内、外框架组件的等惯量约束条件和振动灵敏度等角度，探讨了检测质量对陀螺性能的影响，为微机械框架振动陀螺的设计提供了理论依据。
3) constraints
约束条件
1.
Application of various constraints in videogrammetry for the profilement of gossamer inflatable spacecraft antenna;
多约束条件在薄膜充气天线面形测量中的应用
2.
The application of constraints of scaler to flat panel displayer;
平板显示器中定标器的时序约束条件
3.
Methods to Deal with Constraints in Overload Control Systems of Winged Missile;
飞航导弹过载控制系统中约束条件的处理方法
4) constraint condition
约束条件
1.
A analysis on structure and constraint condition of the management models of water environment;
水环境管理模型的结构与约束条件分析
2.
A study on axiomatic designing method under constraint conditions;
约束条件下公理化设计方法研究
3.
Analyses on the influence of vibration modal tests under different constraint conditions
不同约束条件下的变速器箱体振动模态试验分析
5) Constrained Condition
约束条件
1.
The hybridize genetic and non-smooth algorithm of min-max problem under limited and constrained conditions
带界约束条件min-max问题的混合遗传非光滑算法
2.
Based on the dynamic property of framework, a dynamic optimized calculation of multistoriedframewouk is made with the span of framework and sit f fness of beams and columns as design variable, andwith stress,displacement, frequency and size constraints as constrained conditions.
在考虑框架动力特性的基础上，将框架跨度与梁、柱刚度作为设计变量，且约束条件全面考虑了应力、位移、频率和尺寸约束。
3.
This essay presents the problems and all the constrained conditions that should be taken into consideration when arranging courses.
本文描述了排课问题及在设计排课系统时应考虑的各种约束条件,在分析其它排课算法的同时结合孝感学院实际情况,提出了一种基于优先级的自动排课算法,并以该算法设计了一个排课系统。
6) constraint conditions
约束条件
1.
Quality assessment of linear features’ simplification algorithms based on constraint conditions;
基于约束条件的线要素化简算法质量评估
2.
The rational selection of cutting quantity in lathe cutting, the determination of objective function in majorizing design and the form of constraint conditions are presented.
较详细地介绍了车削时切削用量合理选择、优化设计对目标函数的确定，约束条件的建立，并以切削速度为例，介绍最优切削速度确定。
3.
Aimed at the problems of multivariable and complicated target function and constraint conditions in mechanical optimal design,the mathematical model combing mechanical optimal design with Particle Swarm Optimization(PSO) is constructed.
针对机械优化设计中变量多、目标函数和约束条件复杂而难以求解的问题,建立了基于微粒群算法的机械优化设计的数学模型;并针对传统罚函数法处理约束条件而引起的病态问题,提出一种利用混沌变量来更新产生违约解个体的方式来改进微粒群算法,增加了个体的多样性、避免微粒群算法出现早熟,从而加快算法的收敛速度。
补充资料：等式约束
分子式：
CAS号：
性质：对优化问题中目标函数自变量的取值用等式加以限制的约束。例如优化问题minf(x),x∈En,Ax=M，Bx>N，Ax=M即是等式约束。
CAS号：
性质：对优化问题中目标函数自变量的取值用等式加以限制的约束。例如优化问题minf(x),x∈En,Ax=M，Bx>N，Ax=M即是等式约束。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条