1) axial play
轴隙
2) axial clearance
轴向间隙
1.
Analysis the producing ways of axial clearance of bent axises on X195 diesel;
保证X195柴油机曲轴总成轴向间隙几种生产方式的讨论
2.
The method of eliminating axial clearance,logical fixing configuration and effective guard of ballscrew nut pair are all introduced in this paper.
介绍滚珠丝杆螺母副轴向间隙的消除方法、合理的安装结构和有效的防护装置。
3.
It was found that these faults were attributed to(1) the excess axial clearance of the rolls at the bearing seat,and(2) the excess bouncing resulting from the unbalanced force applied to the rubber mat of the rolls.
经分析,原因是轧辊非传动端轴承座装配的轴向间隙过大,且螺纹公差偏大,所以造成轧辊窜动严重以及原用胶垫受力不均衡,弹跳过大。
3) Bearing clearance
轴承间隙
1.
Calculation of bearing clearance of conical axle flow-distribution pairs in hydraulic pumps with water medium;
水介质液压泵锥形轴配流副轴承间隙的计算
2.
Simulation of impact test bench with pendulum based on bearing clearance model;
基于轴承间隙模型的摆锤碰撞试验台仿真研究
3.
The experiment design of bolster eccentricity and bearing clearance is adopted to get regression equation.
采用二次通用旋转组合设计的方法安排试验,求得其回归方程,然后运用随机方向搜索法对回归方程进行优化,得出锭座偏心和轴承间隙的最优值。
5) axial clearance
轴向游隙
1.
Measuring device for axial clearance of angle contact ball bearings with split inner ring;
双半内圈角接触球轴承轴向游隙测量仪
2.
Discussion on technology of controlling axial clearance of double row tapered roller bearing
控制双列圆锥滚子轴承轴向游隙的工艺探讨
3.
The axial clearance is one of the main parameters of the rolling bearing;measured clearance value is closely related to the measuring method and load.
轴向游隙是滚动轴承的关键指标参数之一 ,测量方法、测量载荷与测得的游隙值的大小密切相关。
6) axial gap
轴向间隙
1.
The experimental investigation of stator clocking effect with different axial gaps shows that the variation of efficiency increases while the mass flow rate increases at fixed axial gap,but the pressure ratio changes little.
本文实验研究了在不同动、静叶间轴向间隙下静叶时序效应对某低速轴流压气机气动性能的影响。
2.
Based on parameter graph modelling axial gap can be analysed by this system during the assembling of turbodrill.
在分析涡轮钻具结构的基础上 ,论述了涡轮钻具的结构和数据的CAD表示方法 ,同时系统采用参数化图形建模方式 ,能方便地辅助分析装配过程中轴向间隙的大小 。
补充资料：单轴各向异性
单轴各向异性是磁晶各向异性的最简单形式，即自发磁化的稳定方向（或易磁化方向）平行于一特殊晶轴。如六方晶系钴的自发磁化方向平行于 C轴(见晶体结构)，这就表现出强的单轴各向异性。磁性材料的单轴各向异性值一般都低于其磁晶各向异性值，为103erg/cm3量级。磁性材料经磁场热处理或强的冷加工而产生的感生各向异性，都属于单轴各向异性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条