1) airdraulic
气液联动的
2) gas-liquid linkage
气液联动
1.
According to GB 50251-2003 "Design Requirements of Gas Transmission Pipeline Engineering", the analysis focuses on the gas-liquid linkage execution structure of route shut-off valves of SHEFER in America and LEDEEN in Italy.
根据GB50251-2003《输气管道工程设计规范》,通过对美国的SHEFER和意大利的LEDEEN的线路截断阀气液联动执行机构的分析,结合实际测量数据和模拟数据,探讨分析了线路截断阀在实际应用中存在的问题,提出了利用现有技术的解决办法和预防措施。
3) gas-oil valve
气液联动阀
1.
This paper describes the key point of gas-oil valve in daily care and maintenance, including the basic structure, operating procedure, cleaning of filter and replacement, inspection of air-tube and test tube, inspection of hydraulic oil of gas-liquid and oil-level,inspection of voltage of battery,also the problems to be focused on in winter operation.
阐述了气液联动阀的基本结构和工作原理、操作程序、过滤器的清洗与更换、气源管和检测管的检查与吹扫、气液罐液压油及油位的检查、电池电压的检查等日常维护与保养工作要点以及冬季运行应注意的问题。
4) dynamic and hydraulic combined system
气液联合传动
5) Air hydraulic coordinated system
气液联动系统
6) pneumohydraulic
[,nju:mə,hai'drɔ:lik]
气动-液动的,气动液压的;气动液压[的]
补充资料:溢流阀、顺序阀、减压阀的比较
溢流阀 | 减压阀 | 顺序阀 | ||
控制油路的特点 | 通过调整弹簧的压力控制进油路的压力,保证进口压力恒定,p2=0 | 通过调整弹簧的压力控制出油口的压力,保证出口压力p2稳定 | 直控式-通过调定调压弹簧的压力控制进油路压力;夜控式-由单独油路控制压力 | |
出油口情况 | 出油口与油箱相连 | 出油口与减压回路相连 | 出油口与工作回路相连 | |
泄漏形式 | 内泄式 | 外泄式 | 内泄式 | |
进油口状态及压力值 | 常态 | 常闭(原始状态) | 常开(原始状态) | 常闭(原始状态) |
工作状态 | 进出油口相通,进油口压力为调整压力 | 进油口压力低于出油口压力,出油口压力稳定在调定值上 | 进出油口相通,进油口压力允许继续升高 | |
联接方式 | 并联 | 串联 | 实现顺序动作式串联作卸荷阀用时并联 | |
功用 | 定压、溢流或安全作用限压、稳压、保压 | 减压、稳压 | 不控制系统的压力,只利用系统的压力变化控制油路的通断 | |
进油腔压力p1控制阀芯移动 | 出油腔压力p2控制阀芯移动 | 进油腔压力p1控制阀芯移动 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条