1) starting diameter
初直径
2) diameter
[英][daɪ'æmɪtə(r)] [美][daɪ'æmətɚ]
直径
1.
Test Analyses of Diameter Matching of Front Top Roller and Back Top Roller of Spinning Frame;
细纱前后档胶辊直径搭配试验分析
2.
Spinning Test of Big Diameter Spinning Top Roller;
大直径细纱胶辊纺纱试验
3.
The result of the wool yarn fault by the Uster evenness testerand the contrast analysis of the surface diameter;
电容式条干仪与表观直径实测毛型纱线疵点的对比
3) diameters
[英][dai'æmitə] [美][daɪ'æmətɚ]
直径
1.
The measurement and extraction of the section profile features of cylinders are the basis of the evaluation of their diameters,form & position errors and roughness.
圆柱体截面轮廓要素的测量与提取是圆柱体直径、形位误差和表面粗糙度评价的基础。
2.
In this paper,We give odd strong harmonious labeling of trees whose diameters are four.
给出了直径为4的树的奇强协调标号。
3.
At present,there are many methods to produce the multi-differences mixture yarn,but to produce through one spinneret is more economical and with better effects compared with other methods,so the influences of the diameters of the die-spin- ning nozzles o.
研究了同板多异涤纶 POY 的单丝细度及取向度与喷丝孔直径的关系, 得到第一,单丝直径与喷丝孔直径的平方成线性关系,单丝线密度与喷丝孔直径的四次方成线性关系;第二,与粗的单丝相比,细的单丝表现出更高的取向度。
4) initial runoff
初期径流
1.
Rainwater pollution is a problem which should be resolved primarily in urban rainwater utilization system,controlling of initial runoff is a key point to restrict non-point pollutant load in one whole rainfall.
雨水污染问题是城市雨水利用系统要解决的首要问题,而初期径流的控制又是对整场降雨面污染负荷控制的关键。
5) initial pipe diameter selection
管径初选
6) initial radius
初始半径
1.
The initial radius is one of important parameters that have significant impacts on the computational complexity.
它利用了SD内嵌的QR分解结果来得到初始半径。
2.
The calculation formula of plastic radius and ultimate pressure due to expansion of soil mass deduced is with consideration of initial radius.
从柱孔扩张过程中的体积假定,即弹性区和塑性区体积的变化等于扩张引起的体积变化出发推导了考虑初始半径的土体的塑性区半径和极限扩张压力公式,讨论了不同摩擦角、塑性区体应变、刚度比条件下,初始半径对土体的塑性区半径和极限扩张压力计算结果的影响。
补充资料：直径
直径
diameter
直径【创恤md份;八“aMeTp} 1)二次曲线的直径(dian犯terofa涨戈ond一orderclu、℃)是通过平行弦中心的直线.称直径相对被它平分的弦(以及相对这些弦的方向)是共扼的(conju-即te).有心二次曲线的直径在曲线中心彼此相交;无心二次曲线的直径是平行的(或者重合).椭圆和双曲线的直径是通过其中心的直线.抛物线的直径是抛物线的轴以及与轴平行的直线. 2)度量空间中集合的直径(dian犯terofaset)是集合的各对点之间的距离的最小上界.
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条