1) rock bit testing rig
![点击朗读](/dictall/images/read.gif)
牙轮钻头试验钻机
2) roller bit
![点击朗读](/dictall/images/read.gif)
牙轮钻头
1.
Dynamic model of roller bit with nine degrees of freedom;
![点击朗读](/dictall/images/read.gif)
九自由度牙轮钻头动力学模型研究
2.
Computer simulation for the side-cutting of roller bits;
![点击朗读](/dictall/images/read.gif)
牙轮钻头侧向切削的计算机仿真
3.
Model to determine rock drillability by roller bit;
![点击朗读](/dictall/images/read.gif)
牙轮钻头可钻性级值的确定方法
3) rock bit
![点击朗读](/dictall/images/read.gif)
牙轮钻头
1.
The calculation of contact stress of rock bit floating ring journal bearing under disalignment;
不对正情况下牙轮钻头浮动套轴承接触应力计算
2.
Application of computer simulating technology in rock bit floating-ring journal bearings;
![点击朗读](/dictall/images/read.gif)
仿真技术在牙轮钻头浮动套轴承设计中的应用
3.
The coupling function analysis of the thread-locking ring of rock bit on axial load;
![点击朗读](/dictall/images/read.gif)
轴向载荷对牙轮钻头螺纹锁紧环联接性能影响的分析
4) bit cone
![点击朗读](/dictall/images/read.gif)
钻头牙轮
1.
There are many causes inducing rock bit cone break, in which the effect of its machining on the cone is more serious.
造成钻头牙轮破裂的原因是多方面的 ,其中钻头机加工对牙轮开裂的影响较大。
5) roller cone bit
![点击朗读](/dictall/images/read.gif)
牙轮钻头
1.
Simulation of rock disintegrating process by roller cone bits;
![点击朗读](/dictall/images/read.gif)
牙轮钻头牙齿破岩过程仿真
2.
Applicant research of bored piles into the hard rock with roller cone bit;
![点击朗读](/dictall/images/read.gif)
牙轮钻头在钻孔灌注桩进入硬岩中的应用研究
3.
Design and processing control of slide bearing clearance of roller cone bit.;
![点击朗读](/dictall/images/read.gif)
牙轮钻头滑动轴承间隙的设计及加工控制
6) cone bit
![点击朗读](/dictall/images/read.gif)
牙轮钻头
1.
Breaking cuttings mechanism of cone bits and fractal method for rock drillability;
![点击朗读](/dictall/images/read.gif)
牙轮钻头的岩屑破碎机理及可钻性的分形法
2.
Application of deep end-cavity cylindrical roller bearings to cone bits;
![点击朗读](/dictall/images/read.gif)
凹端圆柱滚子轴承在牙轮钻头上的应用分析
3.
Elastohydrodynamic lubrication of tapered roller bearing on new high-speed cone bits;
![点击朗读](/dictall/images/read.gif)
新型高速牙轮钻头圆锥滚子轴承润滑状态分析
补充资料:牙轮钻头
牙轮钻头
rotary drilling bit
yolunzLJantou牙轮钻头(rotary drilling bit)在钻头上装有牙轮,借牙轮的滚动碾压作用破碎岩石的钻孔工具。有单牙轮钻头和多牙轮钻头两种,以三牙轮钻头为最常用,见附图。当钻头回转时,牙轮在孔底滚动,它除以钻头轴线作公转运动外,还绕牙爪的轴颈自旋,牙轮上的牙齿轮番地接触岩石而破碎它。由于钻头在很大的轴压下工作,必须有良好的轴承和可靠的润滑冷却系统。九飞 固定螺钉/啼嘴}汗恤j乡诊;入、心丫 岁月Q心卜入日娜口了~一牙轮 /百衬叼叹反汹侧侣r一背轮 止推块衬套滚珠滚柱牙齿 气冷式牙轮钻头构造图 轴承在牙爪的轴颈上装有多套轴承。径向力的80%靠滚柱轴承承担,止推块用来承受牙轮的轴向力。滚珠轴承则用于把牙轮锁紧在轴颈上,同时也承担小部分的径向力和轴向力。 牙齿有钢齿和硬质合金齿两种。前者只用于中硬以下岩石。硬质合金齿在软岩中用楔形肯;在中硬岩石用锥球形齿;在硬岩及极硬岩石中用半球形齿。随岩石硬度的增加,齿的高度减小,齿的数目增加。 冷却与润滑(l)气冷式钻头,以压缩空气总量的20%一35%通过钻杆沿挡碴管上的网孔进人牙轮的轴承腔内,用以冷却和润滑轴承,其余由喷嘴吹至炮孔底部,用于排碴。(2)储油密封式钻头,用于水孔钻进。轴承是密封型的,在牙爪上端设有储油囊和压力补偿系统,能自动地向轴承注油口
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条