1) mobile seeder
流动播种机
2) seeding plow
自动耕地播种机
3) Fluid seeding
流体播种
1.
Research on application effect of water-retaining agent in fluid seeding of wheat;
保水剂在小麦流体播种中的应用研究
2.
On investigation and experimental study, this paper introduces fluid seeding technique and it’s features in saving water, increasing germination and increasing the survival rate of the seedlings, describes the development and application of water-.
流体播种是一种抗旱、节水、增产的新技术。
4) Seeder
[英]['si:də] [美]['sidɚ]
播种机
1.
Research on improvement and experiment of 2BYF-6 type stubble no-tillage multi-seeder for rape;
2BYF-6型油菜免耕直播联合播种机的改进及试验
2.
Dynamic model for metering process for pneumatic roller-type vegetable seeder;
气力滚筒式蔬菜穴盘播种机吸排种动力学模型的研究
3.
Experimental research on 2BYF-6 type no-tillage rape combine seeder in paddy stubble field;
2BYF-6型油菜免耕直播联合播种机田间试验研究
5) sowing machine
播种机
1.
Study on the improvement of water-saving and anti-drought seed-sowing machine;
节水抗旱施水播种机的改进
2.
【Objective】 The study developed a new type of sowing machine that is capable of dividing the fertilizer into seed fertilizer and base fertilizer and laying them into a deeper depth while sowing.
【目的】研制在播种的同时能将肥料分成种肥、基肥且深施播的新型播种机。
3.
This paper discussed system simulation and reviewed its history development, expatiated its application and study on sowing machine, pointed out the problems in this field.
论述了系统仿真技术的基本概念框架及其发展现状,详细阐述了在播种机领域内开展仿真研究的状况,指出了当前这一领域里存在的问题。
6) planter
[英]['plɑ:ntə(r)] [美]['plæntɚ]
播种机
1.
Design of wheat planter of ridge furrow irrigation;
畦作沟灌的小麦起垄播种机的研制
2.
Design of Rotary Tillage Planter with Double-deck Fertilizer;
双层施肥旋耕播种机的设计
3.
Study on permanent raised bed planter;
固定道垄作小麦玉米两用免耕播种机的研制
补充资料:自动冷镦机、多工位螺栓自动冷镦机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB9166-88、JB/T3053-91 | ||||||
1、冲头夹持器模孔中心线对夹持器后支承面的垂直度(mm) 在100长度上 | 0.008 | 0.01 | 0.015 | >0.015 | |||
2、凹模座模孔中心线对凹模后座支承面的垂直度(mm) 在100长度上 | 0.008 | 0.01 | 0.015 | >0.015 | |||
3、冲头夹持器模孔中心线对滑块行程的平行度(mm) 在100行程上 | 0.016 | 0.02 | 0.02 | >0.02 | |||
4、滑块行程对机身上与凹模座贴合的垂直面的垂直度(mm) 在100行程上 | 0.016 | 0.02 | 0.02 | >0.02 | |||
5、工件头部对工件杆部中心线的偏移量(mm) | <0.20 | 0.20~0.25 | 0.25~0.30 | >0.30 | |||
(二)生产率(件/分) | |||||||
20mm | >80 | 70 | 65 | <65 | |||
30mm | >60 | 50 | 45 | <45 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条