1) hyperpearlitic steel
过珠光体钢
2) pearlitic steel
珠光体钢
1.
Effect of annealing process on microstructure and mechanical properties of severe plastic deformation pearlitic steel wire;
退火工艺对强塑性变形珠光体钢丝组织和性能的影响
2.
Evolution of microstructure and mechanical properties of cold drawn pearlitic steel wires during isothermal treatment
等温处理过程中冷拔珠光体钢丝的组织及其性能
3.
Effect of anneal treatment on the microstructure and mechanical properties of cold drawn pearlitic steel wires
退火处理对冷拉珠光体钢丝组织及性能的影响
3) pearlite steel wires
珠光体钢丝
1.
The microstructure evolution and mechanical properties of SWRH72B pearlite steel wires were studied,the effect of severe deformation on spheroidizing annealing process in SWRH72B pearlite steel wires was also studied.
研究了剧烈冷拉SWRH72B钢丝的组织演变及大变形量对珠光体钢丝球化退火的影响。
2.
Microstructure and mechanical properties evolution of 65Mn and SWRH82B heavily cold drawn pearlite steel wires were mainly studied in this paper.
本文主要研究了65Mn和SWRH82B珠光体钢丝在剧烈冷拉塑性变形条件下，其力学性能及内部组织的演变规律，系统探讨了：①65Mn和SWRH82B珠光体钢丝剧烈冷拉塑性变形的拉拔工艺和配模规律；②剧烈冷拉塑性变形对65Mn和SWRH82B珠光体钢丝力学性能的影响及抗拉强度与硬度之间的关系；③65Mn和SWRH82B剧烈冷拉塑性变形的强化机制；④剧烈冷拉塑性变形对65Mn和SWRH82B珠光体钢丝显微组织演变的影响；⑤剧烈冷拉塑性变形珠光体钢丝渗碳体溶解的热力学和动力学条件。
4) ferrite-pearlite steel
铁素体-珠光体钢
5) ferrite/pearlite steel
铁素体/珠光体钢
1.
The flow stress of ferrite/pearlite steel under uni-axial tension was simulated with finite element method (FEM) by applying commercial software MARC/MENTAT.
应用MARC/MENTAT商用有限元软件,对铁素体/珠光体钢的单向拉伸过程进行了有限元模拟。
6) pearlite heat-resistant steel
珠光体耐热钢
1.
This article mainly aims at introducing the welding methods of pearlite heat-resistant steel,the selection of weld materials and the pre-heated temperature before welding.
主要介绍了珠光体耐热钢的焊接方法、焊接材料的选择、焊前预热温度、焊后热处理及其焊接性能等方面的内容,并针对本厂的生产结构制订12Cr1MoV材料的工艺评定、焊接工艺参数以及焊后热处理工艺等。
2.
The non-destructive carbide phase analysis method for pearlite heat-resistant steel used in the past is improved, and it is easy to manipulate and master.
对过去采用的珠光体耐热钢非破坏碳化物相分析方法进行了改进,其操作简单,宜于掌握,分析结果的正确度及精密度得到提高。
补充资料：珠光体钢
分子式：
CAS号：
性质：这类钢在正火状态下，具有珠光体和铁素体显微组织的钢。该钢种合金元素含量少，工艺性能好，工作温度最高可达600℃，又称珠光体热强钢或珠光体耐热钢。按用途这类钢又可分为锅炉管用钢、气包用钢、紧固件用钢和转子用钢。
CAS号：
性质：这类钢在正火状态下，具有珠光体和铁素体显微组织的钢。该钢种合金元素含量少，工艺性能好，工作温度最高可达600℃，又称珠光体热强钢或珠光体耐热钢。按用途这类钢又可分为锅炉管用钢、气包用钢、紧固件用钢和转子用钢。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条