说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 相对方位显示
1)  heading upward presentation
相对方位显示
2)  azimuth scope
方位显示器
3)  relative azimuth
相对方位
1.
In view of the imprecise measurement of the relative azimuth between projectile and target in the existing correction ammunitions,a new method which can measure the relative azimuth between projectile and target accurately is designed by combining the advantages of CCD and MEMS gyro.
针对现有修正弹药中弹目相对方位探测精度较低的不足,该文结合图像敏感器(CCD)和微机电陀螺(MEMS)的特点,设计了利用CCD与MEMS陀螺组合测量弹目相对方位的方法。
2.
The relative azimuth between projectile and target is the key parameter needed in projectile correction.
弹目相对方位是弹丸修正所需的重要参数。
4)  relative orientation
相对方位
1.
The calculation of relative orientation in far-distance radar and target's simulations
远程雷达与目标仿真的相对方位计算方法
5)  relative motion display
相对运动显示
6)  Relative-motion indicator
相对运动显示器
补充资料:使用基准显示对话框设置基准的显示

使用“基准显示”(Datum Display) 对话框,可以独立于基准图元的名称(标签)指定单个基准图元的显示状态。单击“视图”(View)>“显示设置”(Display Settings)>“基准显示”(Datum Display),打开“基准显示”(Datum Display) 对话框。


对话框中有下列基准显示选项:


基准平面 (Datum Planes) - 显示基准平面及其名称。也可使用配置文件选项 display_planes 来设置。


基准平面标签 (Datum Plane Tags) - 显示基准平面名称。也可使用配置选项 display_plane_tags 来设置。


基准轴 (Datum Axes) - 显示基准轴及其名称。也可使用配置文件选项 display_axes 来设置。
轴标签 (Axis Tags) - 显示基准轴名称。也可使用配置选项 display_axis_tags 来设置。


点符号 (Point Symbols) - 显示基准点及其名称。也可使用配置文件选项 display_points 来设置。


点标签 (Point Tags) - 显示基准点名称。也可使用配置文件选项 display_point_tags 来设置。


坐标系 (Coordinate Systems) - 显示坐标系及其名称。也可使用配置文件选项 display_coord_sys 来设置。


坐标系标签 (Coordinate System Tags) - 显示坐标系名称。也可使用配置选项 display_coord_sys_tags 来设置。


旋转中心 (Spin Center) - 显示旋转中心符号。也可使用配置文件选项 spin_center_display 来设置。


曲线标签 (Curve Tags) - 显示曲线名称。也可使用配置选项 curve_tag_display 来设置。


使用“全选”(Select All) 或“取消全选”(Unselect All) 按钮,可一次显示或隐藏全部基准图元。


在“点符号”(Point Symbol) 下,可以指定想要用于指定点的符号类型。选项有“十字”(Cross)、“点”(Dot)、“圆”(Circle)、“三角形”(Triangle) 和“正方形”(Square)。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条