1) eccentric anomaly
偏心象差
2) quadrantal deviation
象[限偏]差
3) Eccentric Phenomena)
偏心现象
4) eccentric error
偏心误差
1.
In general condition,it should be allowed that eccentric error is larger than ±10% of average air-gap,but over-large eccentric value can produce very much unbalanced magnetic pull,and then increase the deflection of motor shaft,thus critical speed is influenced.
在一般情况下,气隙偏心误差不超过气隙平均值的上下10%是允许的,但过大的偏心值会产生很大的单边磁拉力,导致电机转轴挠度的增加,进而影响电机的临界转速,但许多电机设计人员在计算电机转轴的挠度时,往往忽略单边磁拉力对于挠度的影响,为此,介绍了单边磁拉力产生的原因及对电机转轴挠度影响的计算过程。
5) instantanous center deviation
瞬心偏差
6) Psychological deviation
心理偏差
1.
By introducing the related psychological research achievements into assets pricing field,it s assumed that investors are finitely rational,that there is a real decision-making deviation,and that it s in the assets pricing model based on investor s psychological deviation that abnormal phenomena in capital market are combined with investor s behavior from dif.
不断出现的资产收益可预测性现象逐渐动摇了研究者对投资者完全理性假设的信心,通过将心理研究成果引入资产定价领域,假设投资者有限理性和存在实际决策偏差,基于投资者心理偏差的资产定价模型从不同角度将资本市场中出现的异常现象与投资者的行为联系起来。
2.
In the process of classroom instruction appraisal,the cognitive deviations of the appraisers affect the appraisal accuracy,and the psychological deviations of the students appraised can also bring inaccuracy.
课堂教学评价过程中,评价者的认知偏差影响到评价结论的准确性,评价对象的心理偏差也会使评价失真,从而导致评价结果的不准确。
3.
This paper generally analyzes the causes of students behavior and psychological deviation by investigating students deregulation and primarily discusses the ways of rectifying students behavior and psychological deviation in the process of physical education.
从对学生违纪情况调查,分析学生的行为与心理偏差原因,探讨体育教学中矫正学生行为与心理偏差的方法。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条