1) Build Up Period SA
交箱期
2) container leasing
超期箱
3) Build Down Period
还箱期
4) Period of Container Leasing
租箱期
5) Exceeding The Time Limit Occupies The Box
逾期占箱
6) skew box girder
斜交箱梁
1.
Three-dimensional simulation calculation of skew box girder and static load test;
斜交箱梁的三维实体仿真计算及其静载测试
2.
Using CB shell element and layered model,the behaviors of cracking,yielding and destroying procedures of a three-span PC continuous skew box girder are analyzed considering the material and the geometry nonlinearity.
基于CB壳单元,采用层状模型模拟预应力混凝土结构,考虑材料和几何双重非线性效应,有效地模拟了三跨连续斜交箱梁的开裂、屈服和失效的全过程。
3.
Based on shell63 element of ANSYS,skew box girders with thirty degrees and fortyfive degrees of skew are analyzed respectively to investigate longitudinal and transversal distributions of shear lag effect under concentrated or uniform force,and they are compared with the corresponding right box girders.
运用ANSYS程序中的shell63单元,分析了集中荷载、均布荷载作用下斜度为30°和45°的斜交箱梁剪滞效应的纵、横向分布规律,并与相应正交箱梁进行了比较,结果表明,跨中断面的剪滞系数随着斜度的增大变化不明显。
补充资料：ANSYS壳单元分析箱梁
! Analysis a box beam section with shell elements of ANSYS
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条