1) iron space factor
铁芯填充系数
2) core packing fraction
芯填充系数
3) filling coefficient
填充系数
1.
Researches on filling coefficients for stability of soil stratum permeability;
土体渗透稳定性的填充系数分析计算方法
2.
Based on the comparison between theoretical calculation and test results,this paper suggests that the filling coefficient of c.
通过理论计算与试验结果的对比,建议冠状铆钉干涉配合的填充系数可取为0。
4) fill factor
填充系数
1.
Confirmation of new photodetector and its fill factor;
新型光电探测器及其填充系数的确定
2.
The integration technique is applied to 256×256 PtSi CCD, and has made its fill factor increased by 2.
微透镜与红外256×256PtSiCCD的集成结果表明,微透镜填充系数提高了2。
3.
The results show that the performances of graded gravel mixture are improved significantly after being treated with cement and lime,especially when fill factor is 0.
研究表明,掺加二灰后级配碎石混合料的性能显著提高,特别是二灰的填充系数为0。
5) filling coefficient
充填系数
1.
In the evaluation of gravel filling sand prevention, the filling coefficient is one of important parameters to evaluate gravel filling whether good or not.
在砾石充填防砂评价中,充填系数是评价砾石充填好坏的重要参数之一。
2.
Based on the bulk model of rock resistivity, the experimental formula of porosity was developed, the “filling coefficient”expression was also derived from the consistence of the filling coefficient and porosity.
从岩石电阻的体积模型入手,得到孔隙率经验公式,然后根据“充填系数与孔隙率一致”的概念给出充填系数的表达式。
6) filling coefficients
填充系数
1.
The numerical method of the space-time conservation element and solution element(CE/SE) is deduced to simulate the interior flow of pulse detonation engine(PDE) with different filling coefficients.
推导了守恒元与求解元(CE/SE)方法的计算格式,用于对几种不同填充系数的脉冲爆震发动机内流场进行计算,发现CE/SE方法是一种较好的爆震波模拟方法,能够有效地捕获爆震波等强间断。
2.
Under same excess coefficient α,and various filling coefficients β,the detonation pressures are measured,and the factors influencing detonation pressures are analyzed.
测试了在同一余气系数α、不同填充系数β下的爆震波压力,并对其变化进行了分析。
补充资料：挤压筒填充系数
挤压筒填充系数
filling coefficient of container
J iyatong tianehong xishu挤压筒填充系数(fil一ing coeffieient of con-tainer)挤压筒内孔的断面积同锐坯的断面积之比，即 K二二 一凡式中K为挤压筒填充系数;F:为挤压筒内孔断面积;尸:为锭坯的断面积。金属挤压时，为了便于把锭坯顺利地装入挤压筒内，锭坯的直径应比挤压筒的内径小。在挤压开始阶段，金属首先充满挤压筒，填充系数一般为L06一L15，某些特殊合金可取更大些。填充系数的大小根据挤压方式、挤压筒的大小及挤压制品助组织性能确定。 (温景林)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条