1) authorized manufacturer's test
自行检验
2) proper motion
自行
1.
Taking the PPM catalogue as the initial reference catalogue and using the central overlapping method with the iteration process, we obtained the position and proper motion of NGC7302 and high - precision positions and proper motions of 11 stars around the galaxy.
采用上海天文台佘山40cm折射望远镜所拍摄的6张底片，以PPM星表作为初始参考星表，按中心重叠法进行了归算，得到河外星系NGC7302的位置与自行，以及周围天区11颗星的高精度位置和自行，它们的标准误差均好于30mas和0。
2.
Using the stellar proper motions reduced from the observational data of photographic plates taken with the 40 cm double astrograph of Shanghai Astronomical Observatory, the distribution parameters and membership probabilities of stars in the region of the open cluster NGC6530 are determined on the basis of the maximum likelihood principle and given in tabular form.
利用上海天文台40厘米折射望远镜照相观测资料所得出的恒星自行,按最大似然原理确定了疏散星团NGC6530天区内恒星的成员概率。
3.
Carrying out a kinematical analysis of the Galaxy for proper-motion systems of the FK5 and Hipparcos, a large difference in proper motions between two systems is found, even if the precessional correction to the FK5 system has been considered.
针对地面FK5和空间依巴谷自行系统 ,采用银河系运动学分析方法发现 ,即使考虑了岁差改正的影响 ,两种自行系统之间仍存在很大差异。
3) Self-walking
自行走
4) bicycle racing centre
自行车馆
1.
In this paper,performance-based fire safety design concept was adopted to analyze the fire safety objective that the smoke evacuation system of Laoshan bicycle racing centre should achieve,fire scenarios were designed and the performance of natural smoke evacuation system was studied by using CFD techniques.
采用性能化防火设计思想,分析老山自行车馆大厅的排烟系统所应达到的安全目标,设计了可能发生的火灾场景,使用CFD技术研究自然排烟系统的性能,通过数值模拟给出发生火灾时的流场和温度分布,证实大厅自然排烟系统能够保证人员安全疏散,满足该建筑消防安全要求。
5) bicycle
自行车
1.
Was the injured riding bicycle at the time of accident?;
损伤部位、类型与骑/推行自行车的相关性研究
2.
Design and experiment of snake-shaped spring shocker absorber in bicycle;
自行车蛇形弹簧减震器的设计与实验
3.
Use of insulated iron powders in a bicycle permanent magnet electric motor;
绝缘铁粉在自行车永磁电动机中的应用
6) design by self
自行设计
参考词条
补充资料：验收抽样检验和监督抽样检验标准
验收抽样检验和监督抽样检验标准
standards for acceptance sampling and audit sampling inspection
扣nshou ehoUVa叩Jianyan he iiandu eh以JYang iianyanbi0Ozhun验收抽样检验和监督抽样检验标准(stands记sfor accepteLnce sampling and audit saznpling Ins侧沈-tion)有关抽样检验的中华人民共和国国家标准至1卯8年已达20个。其中验收抽样检验标准有巧个，它们是:①《逐批检查计数抽样程序及抽样表》(GBIT2828一1987)，②《周期检查计数抽样程序及抽样表》(G田T282乡一1987)，③《不合格品率的计量抽样检查程序及抽样表》(GBIT6378一1986)，④《计数序贯抽样检查程序及表》(GBZT8()5l一1987)，⑤《单水平和多水平计数连续抽样检查程序及表》(CBIT 5052一1987)，⑥《不合格率的计量标准型一次抽样检查程序及表》(GBIT 8()53一1987)，⑦《平均值的计量标准型一次抽样检验程序及抽样表》(GBIT 8()54一1卯5)，⑧《不合格品率的计数标准型一次抽样检查程序及抽样表》(GB/T13262一1991)，⑨《跳批计数抽样检查程序》(GWT13263一1卯1)，⑩《不合格品率的小批计数抽样检查程序及抽样表》(GB/T 13么抖一I卯I)，⑧《抽样检查导则》(G田T13393一1卯2)，⑩《挑选型计数抽样检查程序及抽样表》(GBIT13夕场一l卯2)，O《粒度均匀散料抽样检验通则》(G脚T 13732一l卯2)，。(孤立批计数抽样检验程序及抽样表》(GBIT 1523乡一l更抖)，0《计量截尾序贯抽样检验程序及抽样表》(GBIT l63()7一l型拓)。 监督抽样检验标准有5个，它们是:①《产品质量监督计数抽样程序及抽样表》(GBIT 14162一1卯3)，②《产品质量平均值的计量一次监督抽样检验程序及抽样表》(GB/T 14灾盯一l臾抖)，③《产品质量监督小总体计数一次抽样检验程序及抽样表)(CBITI，侣2一1卯5)，④《产品质量监督复查程序及抽样方案》(GBIT163C盼一1性尧刹玉)，⑤《产品质量监督计数一次抽样检验程序及抽样方案》(eBzTI科37一l期)。 在上述的抽样检验标准中，较有代表性的抽样检验标准是GBIT2828、GB/T132以、GBIT6378、GBlT8()54，月41，、侧，J
说明：补充资料仅用于学习参考，请勿用于其它任何用途。