1)  self-correcting code
自校正代码
2)  selfcalibration
自校
1.
The selfcalibration and selfcompensation techniques of thermistor in the anemometor;
风速计中热敏电阻自校自补偿技术
3)  self-correction
自校正
1.
In consideration of the diversity of operating conditions,the multi controlling measures such as process tracing,concentration tracing,self-optimization,self-correction,effect control and friendly man-computer interface should be integrated into the system so as to reach better result in control and make the operation easie
工艺跟踪、浓度跟踪、自寻优、自校正、效应控制等技术,以及友好的人机接口不仅取得了良好的控制效果,也方便了操作。
2.
A self-correction and self-aligning PID fuzzy control system is put forward, which includes a self-correction factor N.
提出一种含自校正因子N的自校正自调整PID模糊控制器;讨论了自校正因子N及PID参数的自调整方法;并利用MATLAB6。
3.
s: This paper dea ls with the ultrasonic stepping motor wi th self-correction function.
自校正超声步进马达是一种新型马达 ,文章介绍了这种马达的基本原理 ,并给出了几个具体的例子。
4)  self-calibration
自校正
1.
A Self-calibration Method of Precision Measurement System for Capacitance Transducers;
高精度电容测微仪的自校正方法
2.
Research on self-calibration of laser tracking measurement system;
激光跟踪测量系统自校正方法研究
3.
Study on control technology of self-calibration for seafloor hydrothermal fluid pH exploration electrode;
用于海底热液pH探测电极自校正的控制技术研究
5)  self-tuning
自校正
1.
Design of self-tuning fuzzy contorl system for rubber extrusion vulcanizater set;
橡胶挤出硫化机组自校正模糊控制系统
2.
Robust self-tuning active queue management mechanism;
一种顽健的自校正主动队列管理机制
3.
Simulation of Self-tuning DMC- PID Superheated Steam Temperature Control System;
自校正DMC-PID过热汽温控制系统仿真
6)  self-calibration
自校准
1.
Covariance Analysis for Enhanced Self-Calibration Orbit Determination;
自校准定轨方法的精度评定
2.
The self-calibration apply to VXIbus D/A module;
自校准技术在VXI总线D/A模块中的应用
3.
A self-calibration method for time grating is presented that eliminates zero drift and g.
提出一种实现时栅自校零与自校准的方法,无需外部高精度基准信号,消除了时栅零点漂移和增益漂移。
参考词条
补充资料：极点配置自校正调节器
分子式：
CAS号：

性质： 它是利用极点配置方法来设计自校正控制系统。由于最小方差自校正调节器存在估计误差，可能造成司F最小相位系统的不稳定。另外，当被控对象的增益很小时，其控制作用又可能过大。极点配置自校正调节器可以克服这些缺点。极点配置自校正调节器的设计原则是将最小方差控制器改为使闭环传递函数等于所希望的形式，使系统的极点分布在要求的位置上。 

说明：补充资料仅用于学习参考，请勿用于其它任何用途。