2) overhanging shaft extension
悬伸轴伸
3) Uniaxial tension
单轴拉伸
1.
Numerical simulation of fracture propagation of rock under uniaxial tension;
岩石单轴拉伸破坏过程的数值模拟
2.
A series of ratcheting tests and uniaxial tension tests were conducted on 63Sn-37Pb at room temperature,and the effect of loading history on ratcheting strain rate and elongation of material was observed.
在室温下通过对63Sn37Pb进行一系列棘轮实验和单轴拉伸实验,得到加载历史对材料棘轮应变累积速率以及延伸率的影响关系。
3.
In this work, three methods including bulge testing, uniaxial tension testing a.
为了获得此类多孔膜的弹性常数,本文用鼓膜法结合散斑干涉实验方法、单轴拉伸结合双光束干涉法和多普勒测振仪三种方法测量氧化铝多孔膜的弹性模量,得到的宏观弹性模量基本相同,并对三种方法的优缺点进行了比较,分析了多孔氧化铝膜与块状氧化铝材料或致密氧化铝膜力学性能的差异。
4) Axial tension
轴向拉伸
1.
Experimental study of butt-welded connections subjected to axial tension
轴向拉伸作用下对接焊缝连接性能的试验研究
2.
Experiment of butt-welded connections subjected to axial tension
轴向拉伸作用下对接焊缝连接性能的试验
3.
In this paper, the measurement of complete stress deformation curves of axial tension of large size concrete specimen (250?mm ×250?mm) for the Three Gorges Project is performed successfully by use of a self designed tension apparatus.
采用自行组装的轴向拉伸装置成功地测得三峡三级配混凝土轴向拉伸应力变形全曲线 (试件截面尺寸为 2 5 0mm× 2 5 0mm) ,并根据实测资料进行数学拟合 ,建立了形式较为简单、参数求解方便、具有工程实用价值的数学表达式 。
5) overhang shaft
悬伸轴
1.
For resolving the problem of bending deflection of overhang shaft,it is macroprogram that is applied to compensate the errors of machining deflection timely.
为了解决悬伸轴较大的弯曲变形问题,应用宏程序编程适时补偿切削变形误差,从而获得较高的加工精度,并能提高效率,降低成本,达到了预期的目的。
6) multiaxial stretching
多轴拉伸
1.
The multiaxial stretching of polymer film was planar stretching in polymer processing,and it was very important to set up the constitutive model with the development of polymer solid processing,which was not reported yet.
本文介绍了聚合物多轴拉伸网格模型的研究进展,然后建立起聚合物多轴拉伸网格模型,并在此基础上阐述了Ball模型参数的确定以及模型的实验验证,为聚合物多轴拉伸的研究提供了有益的指导。
补充资料：前伸峰、伸舌头峰
分子式：
CAS号：
性质：又称前伸峰、伸舌头峰。前沿平缓，后沿陡峭的不对称色谱峰称前沿峰。与非线性吸附等温线相对应的色谱峰，可能出现在前延峰。
CAS号：
性质：又称前伸峰、伸舌头峰。前沿平缓，后沿陡峭的不对称色谱峰称前沿峰。与非线性吸附等温线相对应的色谱峰，可能出现在前延峰。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条