1) terminal temperature
终始温度
2) initial temperature
初始温度
1.
Na_8+Na_8 collisional dynamics at different initial temperatures;
不同初始温度时Na_8+Na_8团簇碰撞动力学研究
2.
The initial temperature distribution function of the foundry moulds when heat radiated and infused by hot iron are put forward.
提出了铸型受热辐射和铁水浸泡的初始温度分布函数，并考虑了结晶潜热和强制冷却工艺等因素，使模拟精度高，误差在５％以内，为研究厚大断面球铁铸件的凝固规律提供了较可靠的参考依据。
3.
How to determine initial temperature and adiabatic temperature rise is one of the most principal factors for RCC(Roller Compacted Concrete) dam,which will influence the accuracy and quantity of simulation analysis for temperature field.
碾压混凝土浇筑层的初始温度和绝热温升是碾压混凝土坝设计中的常见问题之一,直接关系到温度场仿真计算的精度和计算量问题。
3) initial temperature
起始温度
1.
This paper proposes that the initial temperature T i of gear is rising gradually during laser scanning tooth by tooth.
提出了齿轮激光淬火逐齿扫描时每个轮齿的“起始温度Ti”的渐变性。
2.
The impact of the initial temperature on the measurement results was also discussed.
文章通过依据不同标准所规定的测试方法进行塑料热变形温度(HDT)测量,找出测量结果之间的规律;同时研究了测量热变形温度过程中使用的硅油的黏度对测量结果的影响,提出更换硅油频率的建议;还探讨了测量起始温度对测量结果的影响。
4) original temperature
原始温度
1.
It uas proposed that the original temperature.
本文探析了影响沼气爆炸极限的诸因素 ,认为沼气的原始温度、原始压力、含氧量、惰性介质、容器的几何尺寸、能量特性等是最主要的影响因素。
5) initial forging temperature
始锻温度
1.
Based on a series of simulation the influence of forging shape on final forming,the influence of friction factor,press speed,initial forging temperature on maximum forming force were analyzed,then the forming process was divided into four phases.
利用有限元数值模拟软件DEFORM-3D,分析了预压坯件形状对终成形效果的影响,研究了摩擦因数、锻造速度、始锻温度对终成形最大载荷的影响规律,解析了该大型铝合金壳体成形过程的4个阶段。
2.
Based on the simulation software DEFORM-3D, the influence of initial forging temperature on forming force, the influence of web thickness and web position on stress, damage factor and forming force were analyzed.
利用数值模拟软件DEFORM-3D,分析了始锻温度对最大成形载荷的影响规律,连皮厚度、连皮位置对齿轮成形时的最大应力、最大损伤因子、最大成形载荷的影响规律。
3.
The influence of main technique parameters in the forming process was researched and the appropriate initial forging temperature of 480 ℃ and hold down speed of 10 mm·s-1 were determined.
本文使用DEFORM-3D软件对锻造铝合金轮毂摆动辗压制坯过程进行数值模拟,考察了主要工艺参数对成形过程的影响,并确定了合理的始锻温度480℃和压下速度10 mm。
6) initial temperature
超始温度
补充资料：善始令终
1.同"善始善终"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条