1)  paper conversion,paper converting,paper processing
纸张加工
2)  paper
纸张
1.
A three-dimensional evaluation of the apparent smoothness of paper;
纸张表观平滑度的三维评价
2.
Investigation into the physical property and surface structure of AAL-TDI-PENpolyurethane treated paper;
乙酸木素-TDI-PEG聚氨酯化纸张物理性能和表面结构的研究
3)  paper properties
纸张性能
1.
Effects of white water treatement on the paper properties of mechanical pulp;
白水处理对机械浆纸张性能的影响效果
4)  pH of paper
纸张pH值
1.
The pH of paper and the pH of dampening liquid also have remarkable influence.
因此,本文就纸张和润湿液的pH值对印刷质量的影响,和印刷中所需的最佳pH值,以及纸张pH值和润湿液pH值之间的相互关系加以探讨。
5)  paper dyeing
纸张染色
6)  paper strength
纸张强度
1.
The relationship between the properties of montmorillonite and its m icroparticle retention effects on furnish together with the necessity of develop ing montmorillonite-based microparticle retention system, the factors affecting the application of it and the effects of using the microparticle system on rosi n sizing and paper strength was discussed.
论述了开发蒙脱石微粒助留体系的必要性、蒙脱石性质和来源对其微粒助留作用的影响、影响蒙脱石微粒助留作用的因素和采用蒙脱石微粒助留体系时对松香施胶和纸张强度性质的影响。
2.
This paper mainly describes the effect of the application of the binary paper strengthening system—cation\|polyacrylamide(CPAM) and carboxymethyl cellulose (CMC).
通过控制CPAM的合成条件 ,加入CMC ,研究CPAM CMC二元体系的添加量、浆料初始pH值等因素对二元增强体系增加纸张强度的影响 ,找出利用CPAM CMC二元体系增加纸张强度的最佳条件 。
3.
The mechanism which the anionic and cationic surface modifiers both modified the surface of GCC is researched,and studied the applying effect of modified GCC as paper filler The experiment indicated,the filler distinctly improved the filler retention rate and paper strengt
实验表明 ,该改性填料明显提高了填料留着率及纸张强
参考词条
补充资料:CIMATRON E NC加工中加工常用参数设置
在表格中单击右键,然后在子菜单中不选Show Prefered Only可以显示所有的加工参数,如落刀点的设置,螺旋下刀的角度等。
1. APPROACH &RETRACT 在XY平面上的进退刀方式
项目 选项 内容
Contour Approach
在被加工轮廓上的进刀方式 Normal 沿法向进刀
Tangent 沿切向进刀
Bisection 在两段直线的相交处进刀时沿角平分线进刀
Approach进刀距离 当Normal时存在 距离被加工轮廓多远进刀
Retract退刀距离 当Normal时存在 距离被加工轮廓多远退刀
Arc Radius圆弧半径 当Tangent 时存在 切向进退刀的圆弧半径
Extension延伸量 在PROFILE加工时存在 延伸加工轮廓以消除接刀痕
Start Check 在PROFILE加工OPEN CONTOUR时存在 使用一个CURVE或POINT作为限制,防止轮廓延伸误碰到零件上的凸台
End Check
2. CLEARANCE PLANE 设定G00的安全平面
Use Clearance ∨ 使用安全平面
Interal Clearance 内部安全高度平面的使用方式 Absolute 抬刀到绝对安全高度Z=10
Incremental 加工完一层后Z=-15抬刀起来ΔZ=5,即抬刀到Z=-10
Absolute Z 10 如上
Incremental 如上
UCS Name UCS=13-1 本步加工使用的坐标系,不应更改
3. Entry & End Point Z方向落刀的方式
Entry Points
Z方向落刀的方式 Auto 系统自动选择下刀点
Optimized 系统优化选择下刀点,同样的零件比自动的下刀点数目少
User-defined 用户指定下刀点
Ramp Angle 只在Auto时存在 螺旋下刀的螺旋角,90度为垂直下刀
Max. Ramp Radius 当下刀角小于90度时 螺旋下刀的最大螺旋半径
Min Plunge Size 刀具的盲区大小
Dz. Feed Start 落刀时距离被加工层高度多高的距离开始用进给速度走刀
4. Offset & Tolerance 加工余量和加工精度,
Contour(Surface) Offset 加工余量
(Contour) Tolerance 加工精度
5. Tool Trajectory 走刀参数
Z-top 加工的最大高度
Z-bottom 加工的最低高度
Mill Finish Pass 是否精铣轮廓
Down Step 层降步距
Side Step 单层加工上的行距,如果大于刀具直径的一半,则可能留下残料,需要Clean Between Passes
Corner Milling
刀轨拐角处的过渡方式 External Round 刀具外切于轮廓时圆角过渡
All Round 刀具内外切于轮廓时都圆角过渡
All Sharp 刀具内外切于轮廓时都尖角过渡
Milling Direction Climb Milling 顺铣
Conventional Milling 逆铣
Mixed 顺逆混合铣
Cut Direction
当Spiral Cut时存在 Inside Out 从内向外环绕
说明:补充资料仅用于学习参考,请勿用于其它任何用途。