1) anchor coat
增粘涂层(涂布)
2) delaminated clay
涂布粘土
3) bonded coating
粘结涂层
1.
Development of Bonded Coating of Super Fine Powder MoS_2with Graphite;
MoS_2超细粉和石墨的粘结涂层的研制
2.
Wear resisting, anticorrosive and anticohesive properties of the bonded coatings such as PEP, FF 1, FM 110 were evaluated.
评价了PEP、FF 1、FM 110粘结涂层的耐磨、防腐蚀和防粘等综合性能。
4) anti stickiness coating
防粘涂层
1.
The cause of the bubbling of anti stickiness coating on ZL102 casting Al alloy cooking utensils is discussed.
用金相显微镜和电子探针研究了 ZL10 2铸造铝合金炊具防粘涂层部分产品在使用过程中逐渐产生鼓泡的原因 。
5) adhesion coating
胶粘涂层
1.
According to the model of axial symmetry in semi unlimited body, the absorbing moisture stress of adhesion coating under water pressure is studied, which is caused by the difference of absorbing moisture property between filling particulate and adhesion coating basis.
根据半无限体的轴对称模型，对静水压下的胶粘涂层因填充粒子与胶层基体间吸湿性能的差别而引起的吸湿应力进行了研究，以达到饱和吸湿浓度的抗水力磨蚀胶粘涂层为例，对吸湿应力作了数值计算，并进行了结果分
2.
In this paper, the thermal stress between the resinous basis and filled panical in anti-abrasion adhesion coating is analysed, the results show that in the interface the thermal stress reaches the maximum value, and it is possible that too high temperature causes the plasticity of resinous basis and separating between basis and filled particles.
分析了耐磨胶粘涂层基体与填充微粒间的微观热应力。
6) Adhesive Coatings
胶粘涂层
1.
Study on the Slurry Erosion Wear. Properties of the Adhesive Coatings;
耐磨环氧胶粘涂层的浆体冲蚀磨损特性研究
2.
The wear properties of antiwear adhesive coatings under solid particle erosion and slurry erosion condition were studied in this paper.
本文对气固冲蚀和浆体冲蚀条件下耐磨环氧胶粘涂层的磨损特性进行了研究。
补充资料：涂层发粘[制革]
分子式：
分子量：
CAS号：
性质：涂饰良好的革面手感爽滑，若出现粘手感觉，或将革粒面相对重叠，分开时粘滞有声则为涂层发粘。发粘原因是软性树脂用量过大，或涂饰时一层未干又涂一层。
分子量：
CAS号：
性质：涂饰良好的革面手感爽滑，若出现粘手感觉，或将革粒面相对重叠，分开时粘滞有声则为涂层发粘。发粘原因是软性树脂用量过大，或涂饰时一层未干又涂一层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条