1) tank winch
油罐绞车
2) petroleum-drawworks
石油绞车
1.
This dissertation mainly focuses on the modular design method and design reliability of petroleum-drawworks.
最后,详细研究分析了胀套联接的结构组成及工作原理,对胀套的力学模型进行了理论推导,并通过胀套联接在钻机绞车滚筒中的应用实例,验证了胀套联接在石油绞车中应用的可行性。
3) tanks
[英][tæŋk] [美][tæŋk]
油罐车
1.
To prevent the accident,it is recommended that specific tank should be used for specific oils,the inner metal protuberance of tanks should be removed,and flow speed of oils should be controlled to avoid spray.
对一起油罐车灌装柴油时发生闪爆事故进行了分析,原因是油罐车在换装油品前清洗不干净,残存有汽油蒸气,且达到爆炸下限,静电经罐车内壁残留的尖端铁削释放而引发的闪爆事故。
4) heavy oil tank car
粘油罐车
1.
Described are the main technical parameters, structure features, testing and operation of the G 17B type heavy oil tank car.
介绍了G17B型粘油罐车的主要技术参数、结构特点、试验及使用情况。
2.
Described are the development general, car structure, performance, technical parameters, application of new technique and testing of the new type heavy oil tank car with low center of gravity.
介绍了新型低重心粘油罐车的研制概况、车辆结构、性能、技术参数、新技术的采用以及试验情
3.
The main technical parameters of the Russian heavy oil tank cars and the bogies are compared with those of Zhuan K6 bogies in our country.
对俄罗斯粘油罐车及其转向架主要技术参数与我国转K6型转向架主要技术参数进行了对比,经过现场实际测量,确认俄罗斯粘油罐车换装转K6型转向架在我国境内进行原油运输完全可行,但需对心盘连接部分、上下旁承、转向架基础制动装置等进行必要的改造。
5) oil tank truck
油罐车
1.
The safety device on domestically made oil tank trucks and its key points in design are explained through an analytical comparison with BP's oil tank truck standard.
通过与BP石油公司油罐车标准的对比分析,说明国内油罐车安全装置及其设计要点。
2.
There are three major processes in light oil tank truck unloading, namely vacuum pump unloading, submerged pump unloading, and slide pump unloading.
轻油罐车卸槽工艺主要有真空泵卸槽法、潜油泵卸槽法和滑片泵卸槽法。
3.
A method of calculate analysis of transversal stabilization for turning of oil tank truck with irregular elliptical section,inclusing the modeling with four arc, discriminantion of relative position between the liquid linie and the section curve,is in this paper introduced.
介绍了椭圆矩形油罐车转弯时横向稳定性的建模和计算分析方法。
6) oil rail tanker
原油罐车
补充资料：调度绞车
调度绞车
car spotting hoist
d心Odu jiooc陌调度绞车(ear spotting hoist)用在井一牵引矿车和进行矿车编组工作的一种小型纹车。一般功率为10一40kw。主传动系统采用行星减速机构。其结构主要由机架、钢绳卷筒、闸带和操纵手柄组成(见图)。机器由一人操作，牵引钢丝绳工作端部有专用挂钩，另由一人摘挂使其进行牵引。由于该绞车动作简单，很容易实现遥控和自动控制。调度绞车(王荣祥任效乾)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条