1) space heater
小型供暖器
2) small boiler decentralized heat-supply
小型锅炉分散供暖
1.
The comparison between small boiler decentralized heat-supply and large boiler centralized heat-supply is made.
对小型锅炉分散供暖和大型锅炉集中供热进行了对比,大型锅炉集中供热节能效益和社会效益显著。
3) heating form
供暖型式
1.
This article introduces the advantages of box building and describes the heating form; especially the operation of individual household heating of box building is emphasized.
描述了盒子房的供暖型式 ,特别强调了盒子房单户供暖的运行情况。
4) warm type wheat
暖型小麦
1.
Comparison of the physiological characteristics between cold type wheat and warm type wheat under water-stress in seedling stage;
水分胁迫条件下冷暖型小麦幼苗期某些生理特性变化比较
2.
The results show that the air temperature,soil temperature and the illuminance in row of cold type wheat "Shaan 229" are lower than those of warm type wheat "NR9405" during milk-filling and burliness stage.
根据旱棚内外农田小气候观测资料,分析了冷型小麦“陕229”和暖型小麦“NR 9405”的农田微气象特征及其成因。
3.
Field plot experiments were conducted from 2002 to 2004 to study the differences of the canopy temperature between Cold Type Wheat(CTW) and Warm Type Wheat(WTW) under different fertilization conditions.
以冷型小麦品种小偃6号、陕229、RB 6和暖型小麦品种NR 9405、9430为供试材料,通过田间小区试验,研究了4种施肥条件(不施肥、单施磷肥、单施氮肥和氮磷配施)下冷、暖型小麦灌浆结实期冠层温度的差异。
5) Radiator heating
散热器供暖
1.
The arrangement form of internal system of heat-supply substation serving radiator heating system and floor panel heating system is studied with a project example.
结合工程实例,对存在散热器供暖系统和地板辐射供暖系统的热力站站内系统布置形式进行了研究,探讨了传统方式与混水方式两种站内系统设计方式。
2.
The composing of heating load in a typical room with radiant floor heating system or radiator heating system was analyzed.
低温地板辐射供暖地板与外围护结构内表面存在辐射换热 ,散热器供暖房间的散热器附近以及散热器上部热气流与外围护结构存在热流短路。
3.
Study of Indoor Thermal Environment and Energy Consumption with Floor Heating and Radiator heating;
3计算软件对低温地板辐射供暖房间和散热器供暖房间的温度场进行了仿真模拟。
6) heating-radiator
供暖散热器
1.
There are various faults in the running of heating-radiator.
供暖散热器在运行状态时会出现各种故障,需要寻求一种在线快速检测技术。
补充资料：JPL型小型航空橡胶减震器
分子式：
CAS号：
性质：橡胶减震器的一种。采用金属芯柱、外金属板，中间填充橡胶模压制成。结构较轻巧，减震效果好，可承受0.7N的冲击，可耐盐雾、霉菌及核辐射。模压法生产。适用于宇航业、导弹主控仪、地面交通、航海船舶等各种隔震、防冲击的仪器装置。E型、EA型橡胶减震器 E＆EA type rubber mounting 此类减震器是用耐油橡胶压制而成的橡胶金属制品。其黏结强度高、安装方便、寿命长、安全可靠。适用于主机、辅机、仪表设备的隔震和抗冲击。配套于舰艇、船只及陆上设备。
CAS号：
性质：橡胶减震器的一种。采用金属芯柱、外金属板，中间填充橡胶模压制成。结构较轻巧，减震效果好，可承受0.7N的冲击，可耐盐雾、霉菌及核辐射。模压法生产。适用于宇航业、导弹主控仪、地面交通、航海船舶等各种隔震、防冲击的仪器装置。E型、EA型橡胶减震器 E＆EA type rubber mounting 此类减震器是用耐油橡胶压制而成的橡胶金属制品。其黏结强度高、安装方便、寿命长、安全可靠。适用于主机、辅机、仪表设备的隔震和抗冲击。配套于舰艇、船只及陆上设备。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条