1)  aspirator,inhaler,suction appartus,vent fan
吸气器
2)  inspiration
吸气
1.
Aliquation and inspiration tend to occur during the production of heat resistant aluminium alloys due to manufacturing and environmental factors.
在耐热铝合金制备过程中,由于工艺以及环境因素,很容易产生偏析和吸气。
3)  air-breathing
吸气
1.
Experimental investigation of air-breathing valveless pulse detonation engine;
吸气式无阀脉冲爆震发动机试验研究
2.
This paper addressed the nozzle effect on the performance of an air-breathing pulse det- onation engine(PDE)by multi-cycle detonation experiments.
分别对采用不同面积比、不同长径比的收敛喷管、扩张喷管和收扩喷管的吸气式脉冲爆震发动机(PDE)进行了多循环爆震试验研究,着重研究了不同工作频率下喷管面积比和长径比对吸气式PDE性能的影响。
4)  suction
吸气
1.
Based on the test of the single centrifugal fan, suction characteristic of the centrifugal fan in series is carried out.
为此,在离心风机单机吸气性能试验的基础上,进行了离心风机串联吸气性能试验,得出了串联吸气性能与单机吸气性能的关系,以及适于串联的工况条件,为串联风机的参数选择提供了试验依据。
5)  getter
吸气剂
1.
Removing of microdose N_2 in high purity D_2 by getter;
吸气剂法去除高纯D_2中微量N_2
2.
Improvement of Zr-C Getters by Surface Activation;
激活工艺和表面气体压强对一种改性锆石墨吸气剂吸气性能的影响
3.
Improvement of vacuum induction getter melting system;
吸气剂真空感应熔炼系统的改进
6)  desorption gas
解吸气
1.
The cause of forming desorption gas from pressure swing adsorption(PSA)unit of hydrogen plant and its compositions were introduced.
介绍了变压吸附(PSA)解吸气产生的原因,针对其组分特点,提出将其作燃料、作合成甲醇原料、脱二氧化碳后作制氢原料三种利用方案,并对这三种方案的优缺点进行分析。
2.
,Ltd,three gas hydrocarbon suitable for hydrogen production material were selected: natural gas,PSA desorption gas and hydrogen-methane.
通过对中国石化上海石油化工股份公司芳烃事业部2#芳烃联合装置1#制氢装置蒸汽转化法制氢工艺轻油替代原料性质、杂质的分析,筛选出适宜作制氢原料的3种气体烃类:天然气、变压吸附法(PSA)解吸气、甲烷氢。
参考词条
补充资料:补吸气量


补吸气量
inspiratory reserve volume

肺功能检查时,在乎静吸气后再作最大努力吸气所吸入的气量。正常成年人约为1500~2000ml。补吸气量、补呼气量、补呼气量和潮气量组成肺活量。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。